- WLUG - wlug.mailman3.com

SCSI Tape Drive Question
by Marc Hughes May 31, 2001

May 31, 2001

We have a kicking VA Linux 4450 server with a VXA-V17 tape drive in it. Unfortunatly the tape drive isn't seen by linux. It shows up in the scsi bios utilities. There is no mention of a tape drive in dmesg or /var/log/messages after bootup, and it doesn't work when you try something like "mt -f /dev/st0 status". The drive is on scsi channel B, does that make a difference? Is there some way to scan the scsi bus manually? I checked /proc/config.gz and tape drive support is built in. Any ideas, suggestions? -Marc

3 2

Samba question
by Thomas Carey May 30, 2001

May 30, 2001

1 0

Win2k
by Michael P. Gorse May 28, 2001

May 28, 2001

Hi all, I am getting a notebook with Win2k preinstalled, and I would like to repartition the drive and set aside a few hundred megs for a GNU/Linux installation. So I was wondering if Lilo would be able to boot Win2k? Also, how well is NTFS supported in the Linux kernel? Thanks in advance for any help! ---------------------------------------------------------------------------- | |DO what you think is right, not what society expects of you.| | --Michael Gorse / WPI cs '01 / ICQ:22583968 / http://www.wpi.edu/~mgorse/ --

2 1

"Couldn't find ext2 superblock..."
by Dan Crooks May 28, 2001

May 28, 2001

Using Darkstar Resque Disk to boot and look around a RH 6.2 installation. e2fsck -n /dev/hda1 results in Couldn't find ext2 superblock, trying backup blocks... e2fsck: Bad magic number in super-block while trying to open /dev/hda1 Here are the questions: Can I fix the superblock? Or is it re-install time? Duplicate blocks are reported in hda12 (/) when I boot RH 6.2. Is it possible to fix that? RH6.2 boot in rescue mode from CD says fdisk unable to open hda but it is recognized by Darkstar Resque Disk. Unfortunately Darkstar only has partitions defined to hda9 and does not recognize hda12. Is it possible to rename a partition (hda12) to another name (hda5) from outside? I have a second system, Windows based, which allows me access to the internet for downloads, email, etc. Is there a way to download utilities on the Win machine and then execute them from a floppy on the Linux machine either booted into rescue mode from RH or from Darkstar floppy? Thank you in advance for any assistance, guidance or direction. Dan Crooks

1 0

***NEW*** WLUG website
by Andy Stewart May 27, 2001

May 27, 2001

HI everybody, I am hoping that the transition to the new WLUG website was completely painless for you users. You will know that you are seeing the proper site if ***NEW*** appears near the top of the page. The DNS updates should have propagated around the Internet by now, so everybody should be seeing this. If somehow you are seeing the ***OLD*** site, please let me know and copy Chuck Anderson (cra(a)wpi.edu) also. Thanks, Andy -- Andy Stewart, Founder Worcester Linux Users' Group Worcester, MA USA http://www.wlug.org

1 0

XEmacs question - gnuserv/gnuclient
by Andy Stewart May 24, 2001

May 24, 2001

HI gang, I'm running XEmacs 21.1.8 and am playing with gnuserv/gnuclient. Within XEmacs, I do M-x gnuserv-start (which seems OK). In a terminal window on the same machine, I type gnuclient and another XEmacs window pops up quite quickly (as I expect). However, I can't get this to work from another machine on my home network. I played with the xauth stuff and also tried setting the GNU_SECURE environment variable to no avail. Clearly I've done something wrong but I don't know what. Can somebody walk me through the steps? I'm expecting that if I run gnuserv on machine 'tux' that I can set the security so that I can access that gnuserv process from machine 'andypc' by typing the correct incantation of the gnuclient command on 'andypc'. Thanks in advance, Andy -- Andy Stewart, Founder Worcester Linux Users' Group Worcester, MA USA http://www.wlug.org

2 1

Hostname
by Michael Long May 22, 2001

May 22, 2001

Thanks for the help with realaudio. Now it is working fine. My next question concerns how the hostname is published. When I look at the DHCP clients table provided by my router software the windoze boxes have published their hostname correctly but my linux box has published an incorrrect name. When I look at /etc/HOSTNAME the name is 'zeus' however then name that shows up in the clients table is '80'. What am I missing? thx, --mike

2 4

Question about employment opportunities
by Pierce C. Barnard May 22, 2001

May 22, 2001

Hi, I recently re-subscribed to the WLUG users newsletter. I would like to address the following question to all of the network administrators who are members of the WLUG: 1.) What is the best way to become a system administrator? 2.) What exact skills does an employer look for in a perspective client to be a system administrator? 3.) What advice and experience can you share with me? Thank you for your time.

1 0

Re: Wlug digest, Vol 1 #64 - 2 msgs
by Jim Stith May 21, 2001

May 21, 2001

compaq deskpro - the sequel; i have a viewsonic e771 monitor connected to the deskpro. i checked viewsonic's specs and found horizontal range 30-70khz vertical range 50-120hz both are what rh 70 installs and it does find the 771 although it is called e771-2 by rh. video card is a matrox mellinnium g200(generic) which is correct. i am using 16 bit 800x600. the pop sound is more like the monitor shutting off than any sort of safety device. the reason i want to install graphics is that i want to use webmin for configuration of samba apache etc. i am assuming that graphics has to be installed to use webmin. any other suggestions based on the info. above would be appreciated. thanks jim s. wlug-request(a)mail.wlug.org wrote: > > Message: 1 > To: wlug(a)mail.wlug.org > Subject: Re: [Wlug] compaq deskpro > From: Josh Huber <huber(a)alum.wpi.edu> > Date: 17 May 2001 15:00:50 -0400 > Reply-To: wlug(a)mail.wlug.org > > Jim Stith <stith2(a)earthlink.net> writes: > > [snip] > > In addition to what other people are saying, I have to ask -- why > would you want to install X on a server? > > Save disk space, save memory, and keep things simple. If the console > works, just use it. :) > > -- > Josh Huber > > --__--__-- > > Message: 2 > Date: Fri, 18 May 2001 07:30:32 -0400 > From: doug waud <douglas.waud(a)umassmed.edu> > To: wlug(a)mail.wlug.org > Subject: Re: [Wlug] compaq deskpro > Reply-To: wlug(a)mail.wlug.org > > Hi > > > everything loads fine but when the system tries to go into x and give me > > a login screen, the monitor makes a poping sound and the screen goes > > blank. > > As several responses have indicated already, you are probably driving > the monitor at the wrong frequency. This can be very dangerous (you > can cook a monitor this way) but perhaps not in your case since that > "popping sound" is probably the monitor being new enough to cut itself > off when mistreated. > > In any case, what you have to do is find out the allowable hsync and > vsync > frequencies of the monitor. Since the computer is second hand (I assume) > you may not have the manual. In that case, look on the monitor for some > sort of manufacturer/model number and feed that into google. With luck > and a bit of poking around you should be able to find a spec sheet or > table and get the hsync and vsync frequencies (I found Compaq was not > too shabby when faced with the same issue with my daughter's computer > and a Linux install). Once you have those values, you can tell the > install program what to use (I don't use Red Hat, so I can't give you > chapter and verse here; XF86Config is more generic but a tad cryptic. > If you have to go the latter route, feel free to touch base with me > (probably directly to save traffic to the whole group) and we can, > if necessary, walk through the various steps in XF86Config. > > Incidentally, I vaguely remember that my daughter's Compaq (a Presario) > had a bastard video chip which confused SuSE 6.3 but which 7.0 was > able to deal with. I suspect your box is old enough that this will > not be a problem. > > Finally, Compaq is good about providing manuals. I went into google > and entered compaq deskpro and got to the Compaq site > > which, in turn, had a link to a downloadable pdf manual. > > I suspect you may have to be a bit more specific as to model of > compaq deskpro but you should be able to get the equivalent for > your particular box. Ditto for monitor. This way you can give > the install program hints as to both the video chip and the > sync frequencies. > > Hope this helps a little. > > > i have been going through the faq's and the only thing i have found out > > is that compaq did some strange things around the mbr. > > I don't think this is anywhere near the mbr. > > doug > > PS I agree with John Huber's point that X is unnecessary (and perhaps > even in the way) on a server. However, I can also understand why you > might > want to get X going simply because, like Mount Everest, it's there :-) > > -- > Douglas R Waud > 17 Lantern Lane, Shrewsbury, MA, 01545-2006 > http://www.ummed.edu/pub/d/drw/ >

2 1

New WLUG website
by Andy Stewart May 20, 2001

May 20, 2001

HI everybody, The WLUG website has been moved to a new location. I'd like to thank Rob Bellville for hosting the WLUG website for us for the last 3.5 years! Unfortunately, the ISP that Rob was using is "going away" so the site needed a new home. Chuck Anderson has volunteered to host the WLUG website on his machine - thanks, Chuck! I will still maintain my role to keep the site up to date with meeting announcements and such. The change should be totally transparent to all of you. You will continue to access the site via: http://www.wlug.org You will know if you are seeing the new site since it says "**NEW**" near the top. As the DNS change is propagated around the Internet, eventually you'll all see the new site. Don't freak out if you don't catch the new site immediately...they both have identical content. I won't remove the files from the old site just yet until we're sure that the transition has been completed successfully. If you have problems accessing the site, please let me know. Thanks, Andy -- Andy Stewart, Founder Worcester Linux Users' Group Worcester, MA USA http://www.wlug.org

1 0