- WLUG - wlug.mailman3.com

Printing problems

by Don Peterson

Hi All, I am having trouble when printing big batches of documents, these are over 20 pages. Everything starts off fine, but then printing stops usually around page 18 to page 22. If I reprint the batch a different number of pages will print, but never all of them. Like I said I usually get anywhere between 18 to 22 pages. I've noticed if I restart the lpd service I can get the batch to reprint fully once. But then when the next batch prints I start having trouble again. Does anyone know if there is a spool limit with lpd? I know you are going to say use CUPS, but I don't want to mess around with my production servers if I don't have to. Any suggestions are appreciated. Thanx, Don

Dec. 1, 2004

Re: [Wlug] PCI-X under Linux

by Brian Waite

On Fri, 26 Nov 2004 14:55:36 -0500 (EST), Carlton C. Stedman II <sageman(a)wpi.edu> wrote: > I was just wondering if anyone had any success using PCI-X/PCI-Express > cards under linux. I was looking through the kernel and don't see any > specific settings strictly for PCI-X bus. I wonder if they *just work* > with PCI support enabled, as AGP does. > > I'm specifically interested if anyone has got hardware 3D acceleration > working with a PCI-X video card. I'm looking at getting a mid-range NVidia > card, since their drivers are at least useable under linux, compared to > the atrocious performance and glitches the ATI proprietary drivers have > (and the open drivers being worked on are not overly worried with the card > I have, and the R300 driver doesn't have any sort of 3D acceleration right > now). > > As far as I can understand from the docs on nvidia's website, it seems > like it'll just work, but was interested if anyone had any success. In > particular I'm looking at the nvidia 6600gt series. Any input would be > much appreciated. Thanks. Carlton, I use PCI-X cards here at the office. Most of the support for PCI-X is relegated to the specific platform support areas. For example I use PowerPC 74xx processors on Marvell bridges and it works. You might need to do some research on your specific combinations, but being x86 based you'll probably have support. I can't say I've tested any Nvidea cards though so I can be of limited success. Thanks Brian

Nov. 29, 2004

PCI-X under Linux

by Carlton C. Stedman II

I was just wondering if anyone had any success using PCI-X/PCI-Express cards under linux. I was looking through the kernel and don't see any specific settings strictly for PCI-X bus. I wonder if they *just work* with PCI support enabled, as AGP does. I'm specifically interested if anyone has got hardware 3D acceleration working with a PCI-X video card. I'm looking at getting a mid-range NVidia card, since their drivers are at least useable under linux, compared to the atrocious performance and glitches the ATI proprietary drivers have (and the open drivers being worked on are not overly worried with the card I have, and the R300 driver doesn't have any sort of 3D acceleration right now). As far as I can understand from the docs on nvidia's website, it seems like it'll just work, but was interested if anyone had any success. In particular I'm looking at the nvidia 6600gt series. Any input would be much appreciated. Thanks. CCS -- Carlton C. Stedman II, sageman(a)wpi.edu "To iterate is human, to recurse, divine." -- L. Peter Deutch

Nov. 26, 2004

Linux Job Opportunity

by Andy Stewart

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 HI Everybody, I am posting this for a technical recruiter. If you have interest in the position, or know someone who does, please contact the recruiter directly. ====start===== My name is Tom Di Filippo. I am a technical recruiter in the Boston area. I am conducting a confidential search for one of my client companies that is specifically looking for several Software Engineers with desktop Linux experience. Below is a brief overview of what they are looking for. If you or any of your colleagues are interested in hearing more about these opportunities please contact me directly. Thank you in advance for your help. Senior/Principal Engineer, Linux Client (positions at various levels) * Will design and implement portable runtime environment on a Linux desktop platform * Experience with any of the following: Java, Swing, JNI, C++, MFC, ATL, COM, ActiveX. * IE Browser Control and/or Mozilla Geiko engine. * Embedding Media Players into client applications. * Multithreading, X Windows Window Manager development. * Linux device driver development and integration Kind regards, Thomas Di Filippo Market Manager, Client Services (IT and Engineering Staffing) Kforce Professional Staffing 20 Mall Road, Suite 400 Burlington, MA 01803 (781) 359-1707 tdifilippo(a)kforce.com ====end===== - -- Andy Stewart, Founder Worcester Linux Users' Group Worcester, MA USA http://www.wlug.org -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (GNU/Linux) iD8DBQFBo9GsHl0iXDssISsRArtgAKCBx+gDu6gDgUsuz0o1/eONNVa9wwCeKR3r +c2BVq+82puWli3hzTODygU= =Y8uw -----END PGP SIGNATURE-----

Nov. 24, 2004

Re: [Wlug] Linksys WPC11 v3 Wireless Card in SuSE 9.1

by Andy Stewart

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 On Monday 15 November 2004 6:53 pm, Chuck Haines wrote: > Has anyone gotten a WPC11 ver 3 wireless card to work in suse 9.1? > YaST detects the card, however I cannot get it to use WEP correctly > and since both WPI and my home network require it, I'm outta luck > right now. Any help with this would be much appreciated. > > Chuck HI Chuck, I am using an Orinoco Silver wireless card with SuSE 9.1 on my laptop. I am using WEP, so I hope my comments will be helpful even though my card is not the same as yours. First, is it feasible to temporarily turn off WEP on the card and on the home network and make your card work with your network that way? This will insure that you have the proper kernel modules installed, the card isn't broken, etc. Note that the range of this card is IMHO rather poor, so stay close to the wireless access point. When you configure the card via YaST, you should see your config info in the /etc/sysconfig/network directory. For my system, the file is ifcfg-wlan-bus-pcmcia. In that file, note that WIRELESS_KEY_n (0<=n<=3) should be equal to the null string for disabled WEP. I also have STARTMODE='hotplug' to ease my life. The WIRELESS_MODE is 'Ad-hoc'. There should be a value for WIRELESS_ESSID specific to your network. If that works (and please let me know if it does), then I was able to enable WEP by the following settings: WIRELESS_KEY_0="A1B2C3D4E5" where you would put the 5 hex bytes of your key between the double quotes. For some reason, I have WIRELESS_KEY_LENGTH='128', but 5 hex bytes is only 40 bits, so go figure. I did have a WPC11 card at one time, and I could not get > 40 bit WEP to work at all. I don't know if this is (was) a 'feature' of the WPC11, some limitation of Linux, or my own ineptitude. - -- Andy Stewart, Founder Worcester Linux Users' Group Worcester, MA USA http://www.wlug.org -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (GNU/Linux) iD8DBQFBmVP2Hl0iXDssISsRAn6AAJ9lqNApXvHYtA4527Qep67ui02fkACfTh6m QK/YCIBHRc5VsSZ1tlFViY0= =fsBv -----END PGP SIGNATURE-----

Nov. 16, 2004

Linksys WPC11 v3 Wireless Card in SuSE 9.1

by Chuck Haines

Has anyone gotten a WPC11 ver 3 wireless card to work in suse 9.1? YaST detects the card, however I cannot get it to use WEP correctly and since both WPI and my home network require it, I'm outta luck right now. Any help with this would be much appreciated. Chuck -- Chuck Haines chaines(a)gmail.com ------------------------------------------- Tau Kappa Epsilon Fraternity http://www.tkezm.org WPI Class of 2005 http://www.wpi.edu ------------------------------------------- AIM: CyberGrex YIM: CyberGrex_27 ICQ: 3707881 -------------------------------------------

Nov. 15, 2004

[jmorris@redhat.com: Linux Journal Article]

by Charles R. Anderson

----- Forwarded message from James Morris <jmorris(a)redhat.com> ----- From: James Morris <jmorris(a)redhat.com> To: selinux(a)tycho.nsa.gov Cc: fedora-selinux-list(a)redhat.com Date: Fri, 12 Nov 2004 21:48:49 -0500 (EST) Subject: Linux Journal Article Message-ID: <Xine.LNX.4.44.0411122147260.7482-100000(a)thoron.boston.redhat.com> Reply-To: "Fedora SELinux support list for users & developers." <fedora-selinux-list(a)redhat.com> What's New in Fedora Core 3 SE Linux By Faye Coker http://www.linuxjournal.com/node/7887 -- James Morris <jmorris(a)redhat.com> -- fedora-selinux-list mailing list fedora-selinux-list(a)redhat.com http://www.redhat.com/mailman/listinfo/fedora-selinux-list ----- End forwarded message -----

Nov. 13, 2004

Re: [Wlug] Website whoopsies...

by Andy Stewart

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 On Tuesday 09 November 2004 9:36 am, Keller, Tim wrote: > I won't be able to make it to the meeting because 'm not sure what day > "Thursdayday" is... :-) > > Also the link at the bottom to St IgnuCIUS is broken... Both fixed...thanks for the head's up. Secretly, this is how I insure that people actually *read* the website. :-) Andy - -- Andy Stewart, Founder Worcester Linux Users' Group Worcester, MA USA http://www.wlug.org -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (GNU/Linux) iD8DBQFBkU8uHl0iXDssISsRAuuBAJ0TJzqjeLyIxm8AYRBHS4JwTn5nUgCeNFer AhS0ln2t02zC/qikKXPaDSg= =aQr8 -----END PGP SIGNATURE-----

Nov. 9, 2004

JOB Opening Linux (UML) skills needed

by John Spencer

Hello All, I am doing some networking for an opening I have in northern MA/southern NH. I currently need the following: Sr. level engineer with extensive experience with Linux to work with their application software development team. My client is simulating multiple embedded cards using User Mode Linux (UML) sessions for each processor. Experience with: -User Mode Linux (a must) -Networking experience (a must) -Embedded and host Linux -Writing device drivers under Linux a strong plus -C/C++ programming If you are interested and qualified for this role, please call me or send me an email with your resume so I can contact you with the details. I will not send your resume anywhere without talking to you first. Regards, John John Spencer (978) 256-1113 ext 108 jspencer @ optimaleng.com OPTIMAL ENGINEERING PARTNERS "Your Optimal partner for real-time, embedded and systems development expertise" www.optimalengineering.com Regards, John John Spencer (978) 256-1113 ext 108 jspencer(a)optimaleng.com OPTIMAL ENGINEERING PARTNERS "Your Optimal partner for real-time, embedded and systems development expertise" www.optimalengineering.com

Nov. 9, 2004

Website whoopsies...

by Keller, Tim

I won't be able to make it to the meeting because 'm not sure what day "Thursdayday" is... :-) Also the link at the bottom to St IgnuCIUS is broken... Later, Tim.

Nov. 9, 2004

REMINDER: WLUG Meeting - Thursday!

by Andy Stewart

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi Everyone, We'll be having our next WLUG meeting on Thursday, November 11th at 7:00 PM in the usual place. Chuck Anderson is going to talk to us rather informally (a la the Gentoo meeting) about what is new and different in Fedora Core 3. He'll also have a PC or two for a live demo. Coming in December: Our guest speaker at the December 15th meeting will be Jon 'maddog' Hall. If you never come to another WLUG meeting, be sure you make it to this meeting! maddog is a fantastic speaker that you don't want to miss. He has spoken at several WLUG meetings in the past and the feedback has been universally positive. Please see the WLUG website for more details about maddog's talk. Starting in January 2005: It looks like our meeting location will be used for a class on Wednesday evening. It may be possible for us to find another location on campus for our Wednesday meetings. Another possibility is to have occasional meetings on Monday evening. Right now, we alternate between Wednesday and Thursday evening. I know that if we changed to Mon/Thurs meeting nights, some folks would like it and others would not. There's really no way to make everybody happy here, except perhaps to find another campus location for Wednesday evening meetings. Stay tuned...nothing is definite yet. Later, Andy - -- Andy Stewart, Founder Worcester Linux Users' Group Worcester, MA USA http://www.wlug.org -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (GNU/Linux) iD8DBQFBkAlbHl0iXDssISsRAtpNAJ4393ZnBSizHZIWrUK0KTx3YOV/7gCfd1lL oPBP1OtzG93IQVrlPYQ7QNU= =QKLg -----END PGP SIGNATURE-----

Nov. 9, 2004

SSH stops working?

by Skip Gaede

Hi Folks, I have both Linux and WXP on my home machine and do remote maintenance on a Linux gateway. The linux gateway is configured for doing IPSEC as well as SSH. Some time in the past few months, SSH has ceased to work between both WXP and Linux on my system and the remote gateway. I have not changed anything on either end, as far as I can remember. What's strange is that I can setup an IPSEC tunnel to the gateway, and do SSH to the gateway from the local subnet (my IPSEC IP is 168.192.1.128 and I can SSH to 192.168.1.1). If anyone has any suggestions on how to debug this, I'm all ears. Thanks, Skip

Nov. 8, 2004

Re: [Wlug] Re: Announcing the release of Fedora Core 3

by Jeff Kinz

On Mon, Nov 08, 2004 at 04:38:12PM -0500, Don Levey wrote: > jkinz(a)kinz.org wrote: > > Just downloaded the FC3 ISO's from above. In an effort to pay it > > forward a few of you can now download them from: > > > > http://www.kinz.org/FC3Isos.html > > > > discs 2 and 3 are coming. > > > > See the Release Notes in the previous email > > Also keep in mind BitTorrent. It took me about 5 hours today to download > all 4 ISOs and the rescue CD; my machine remains up so that others can do > the same. If even half of those downloading the CDs were to do so via > BitTorrent, and stay up so others can do so, the number of mirrors for the > ISOs increases dramatically, and download time reduces to the capacity of > your pipe. Yup, BT works great. The server I had it on is torn down at the moment, so these iso's are going up on another machine. If I have the opportunity later I'll put up a torrent node. -- Linux/Open Source. Your base belongs to you, free, forever. Idealism: "Realism applied over a longer time period" http://www.scaled.com/projects/tierone/ "Last one into space is a rotten egg!" <a href=http://kinz.org>http://kinz.org</a> Jeff Kinz, Emergent Research, Hudson, MA. ~ ~ ~ ~

Nov. 8, 2004

RE: [Wlug] Re: Announcing the release of Fedora Core 3

by Don Levey

wlug-bounces(a)mail.wlug.org wrote: > On Mon, Nov 08, 2004 at 12:32:40PM -0500, Charles R. Anderson wrote: >> If anyone wants FC3, you can get it here: >> >> http://download.wpi.edu/pub/linux/distributions/fedora/linux/core/3/ >> > > Just downloaded the FC3 ISO's from above. In an effort to pay it > forward a few of you can now download them from: > > http://www.kinz.org/FC3Isos.html > > discs 2 and 3 are coming. > > See the Release Notes in the previous email Also keep in mind BitTorrent. It took me about 5 hours today to download all 4 ISOs and the rescue CD; my machine remains up so that others can do the same. If even half of those downloading the CDs were to do so via BitTorrent, and stay up so others can do so, the number of mirrors for the ISOs increases dramatically, and download time reduces to the capacity of your pipe. -Don

Nov. 8, 2004

Re: Announcing the release of Fedora Core 3

by Jeff Kinz

On Mon, Nov 08, 2004 at 12:32:40PM -0500, Charles R. Anderson wrote: > If anyone wants FC3, you can get it here: > > http://download.wpi.edu/pub/linux/distributions/fedora/linux/core/3/ > Just downloaded the FC3 ISO's from above. In an effort to pay it forward a few of you can now download them from: http://www.kinz.org/FC3Isos.html discs 2 and 3 are coming. See the Release Notes in the previous email -- Linux/Open Source. Your base belongs to you, free, forever. Idealism: "Realism applied over a longer time period" http://www.scaled.com/projects/tierone/ "Last one into space is a rotten egg!" <a href=http://kinz.org>http://kinz.org</a> Jeff Kinz, Emergent Research, Hudson, MA. ~ ~ ~ ~

Nov. 8, 2004

Re: [Wlug] nvidia & digital (?) output

by Brian J. Conway

On Mon, 8 Nov 2004, Bill Mills-Curran wrote: > Can anyone point me in the right direction for configuring my nvidia > card to use the digital output? I just unboxed an LCD monitor, and > I'd like to try the digital video. Is it just a reboot? > > Should I expect much (any?) difference. It should be automatic, just power down, plug everything in, turn it on and it'll be seen. There shouldn't be much in the way of configuration changes. I haven't been able to see any difference between the two, but it's still the "better" way of doing things, and you might as well use the better cable since someone spent the money on an LCD that can use both. Brian J. Conway bconway(at)alum.wpi.edu "LINUX is obsolete" - Andrew S. Tanenbaum, creator of Minix - Jan 29, 1992

Nov. 8, 2004

nvidia & digital (?) output

by Bill Mills-Curran

Can anyone point me in the right direction for configuring my nvidia card to use the digital output? I just unboxed an LCD monitor, and I'd like to try the digital video. Is it just a reboot? Should I expect much (any?) difference. Thanks, Bill

Nov. 8, 2004

[notting@redhat.com: Announcing the release of Fedora Core 3]

by Charles R. Anderson

If anyone wants FC3, you can get it here: http://download.wpi.edu/pub/linux/distributions/fedora/linux/core/3/ Release Notes below: ----- Forwarded message from Bill Nottingham <notting(a)redhat.com> ----- From: Bill Nottingham <notting(a)redhat.com> To: mirror-list(a)redhat.com Date: Mon, 8 Nov 2004 11:13:22 -0500 Subject: Announcing the release of Fedora Core 3 Message-ID: <20041108161322.GA18989(a)nostromo.devel.redhat.com> Precedence: junk Reply-To: mirror-list-d(a)redhat.com, fedora-list(a)redhat.com The Fedora Project and Red Hat would like to announce the third release of Fedora Core. Fedora Core 3 is a general purpose Linux operating system, available for x86 and x86-64 processors. Fedora Core 3, includes: - the 2.6.9 Linux kernel - Xorg 6.8.1 - GNOME 2.8 - KDE 3.3.0 - GCC 3.4 - SELinux The Fedora Project would like to thank the thousands of community members whose testing and contributions have raised the bar of quality and made this release possible. What is the Fedora Project? The Fedora Project is a Red Hat-sponsored and community-supported open source project that promotes rapid development of innovative open source software through a collaborative, community effort. Fedora Core 3 provides a complete Linux platform built exclusively from open source software. Available at no cost, the release serves the needs of community developers, testers, and other technology enthusiasts who wish to participate in and accelerate the technology development process. As a community forum for advanced development, the Fedora Project provides early visibility to the latest open source technology and serves as a proving ground for technology that may eventually make its way into Red Hat's fully-supported commercial solutions such as Red Hat Enterprise Linux. Red Hat contributes development resources, editorial direction and management to the Fedora Project. For more information, see http://fedora.redhat.com/ How Can I Get Fedora Core 3? Fedora Core 3 x86 or x86-64 Downloads are available from: http://fedora.redhat.com/download/ or from the network of mirrors in the Fedora Project distribution system. Users may prefer to download Fedora Core via BitTorrent, or via older file retrieval protocols such as HTTP, FTP, or RSYNC. BitTorrent typically provides faster download speeds than HTTP, FTP, or RSYNC. BitTorrent RPMS for Red Hat Linux and Fedora Core are available with detailed instructions at http://torrent.linux.duke.edu/ From Red Hat: http://download.fedora.redhat.com/pub/fedora/linux/core/3/ Via BitTorrent: http://torrent.linux.duke.edu/heidelberg-binary-i386.torrent http://torrent.linux.duke.edu/heidelberg-binary-x86_64.torrent http://sunsite.mff.cuni.cz/fedora-torrent/heidelberg-binary-i386-iso.torrent http://sunsite.mff.cuni.cz/fedora-torrent/heidelberg-binary-x86_64-iso.torr… See http://torrent.linux.duke.edu/ or http://sunsite.mff.cuni.cz/fedora-torrent/ for other forms. Via HTTP/FTP/RSYNC from mirrors: * North America: * USA: * ftp://fedora.cat.pdx.edu/linux/core/3 * http://fedora.cat.pdx.edu/linux/core/3 * rsync://fedora.cat.pdx.edu/fedora-linux-core/3 * ftp://mirror.stanford.edu/pub/mirrors/fedora/linux/core/3 * http://mirror.stanford.edu/fedora/linux/core/3 * rsync://mirror.stanford.edu/mirrors/fedora/linux/core/3 * ftp://ftp.cse.buffalo.edu/pub/fedora/linux/core/3/ * http://mirror.hiwaay.net/redhat/fedora/linux/core/3/ * ftp://mirror.hiwaay.net/redhat/fedora/linux/core/3/ * rsync://mirror.hiwaay.net/fedora-linux-core/3/ * ftp://ftp.ndlug.nd.edu/pub/fedora/linux/core/3 * http://ftp.ndlug.nd.edu/pub/fedora/linux/core/3 * rsync://ftp.ndlug.nd.edu/fedora-linux-core/3 * ftp://mirrors.kernel.org/fedora/core/3 * http://mirrors.kernel.org/fedora/core/3 * rsync://mirrors.kernel.org/fedora/core/3 * http://fedora.glorb.com/core/3 * ftp://ftp.ale.org/mirrors/fedora/linux/core/3 * http://ftp.ale.org/mirrors/fedora/linux/core/3 * http://mirror.linux.duke.edu/pub/fedora/linux/core/3/ * ftp://mirror.linux.duke.edu/pub/fedora/linux/core/3/ * rsync://mirror.linux.duke.edu/fedora-linux-core/3/ * ftp://videl.ics.hawaii.edu/mirrors/fedora/linux/core/3/ - Hawaii Only * ftp://redhat.secsup.org/pub/linux/redhat/fedora/core/3 * http://redhat.secsup.org/fedora/core/3 * rsync://fedora.secsup.org/core/3/ * ftp://mirror.eas.muohio.edu/pub/fedora/linux/core/3 * http://www.gtlib.cc.gatech.edu/pub/fedora.redhat/linux/core/3 * ftp://ftp.gtlib.cc.gatech.edu/pub/fedora.redhat/linux/core/3 * rsync://rsync.gtlib.cc.gatech.edu/fedora-linux-core/3 * ftp://mirror.newnanutilities.org/pub/fedora/linux/core/3 * http://mirror.newnanutilities.org/pub/fedora/linux/core/3 * ftp://ftp.dc.aleron.net/pub/linux/fedora/linux/core/3/ * http://ftp.dc.aleron.net/pub/linux/fedora/linux/core/3/ * ftp://ftp.net.usf.edu/pub/fedora/linux/core/3 * Canada: * ftp://less.cogeco.net/pub/fedora/linux/core/3/ * http://less.cogeco.net/pub/fedora/linux/core/3/ * ftp://ftp.nrc.ca/pub/systems/linux/redhat/fedora/linux/core/3/ * rsync://ftp.nrc.ca/fedora/linux/core/3/ * http://mirror.cpsc.ucalgary.ca/mirror/fedora/linux/core/3/ * ftp://mirror.cpsc.ucalgary.ca/mirror/fedora/linux/core/3/ * rsync://mirror.cpsc.ucalgary.ca/fedora/linux/core/3/ * http://gulus.USherbrooke.ca/pub/distro/fedora/linux/core/3/ * ftp://ftp.muug.mb.ca/pub/fedora/linux/core/3/ * http://www.muug.mb.ca/pub/fedora/linux/core/3/ * rsync://rsync.muug.mb.ca/fedora-linux-core/3/ * South America: * Chile: * ftp://ftp.tecnoera.com/pub/fedora/linux/3/ * http://ftp.tecnoera.com/pub/fedora/linux/3/ * rsync://ftp.tecnoera.com/pub/fedora/linux/3/ * ftp://mirror.netglobalis.net/pub/fedora/core/3/ * http://mirror.netglobalis.net/pub/fedora/core/3/ * Brazil: * ftp://ftp.las.ic.unicamp.br/pub/fedora/core/3/ * http://www.las.ic.unicamp.br/pub/fedora/core/3/ * rsync://rsync.las.ic.unicamp.br/fedora-linux-core/3 * Europe: * Austria: * ftp://gd.tuwien.ac.at/opsys/linux/fedora/core/3/ * http://gd.tuwien.ac.at/opsys/linux/fedora/core/3/ * rsync://gd.tuwien.ac.at/opsys/linux/fedora/core/3/ * Czech Republic: * ftp://sunsite.mff.cuni.cz/pub/fedora/3/ * http://sunsite.mff.cuni.cz/pub/fedora/3/ * rsync://sunsite.mff.cuni.cz/fedora/fedora/3/ * ftp://ftp.fi.muni.cz/pub/linux/fedora-core/3/ * rsync://ftp.fi.muni.cz/pub/linux/fedora-core/3/ * ftp://ftp6.linux.cz/pub/linux/fedora-core/3/ (IPv6) * ftp://ftp.linux.cz/pub/linux/fedora-core/3/ * ftp://ftp1.skynet.cz/pub/linux/fedora/3/ * Denmark: * ftp://klid.dk/fedora/linux/core/3 * http://klid.dk/homeftp/fedora/linux/core/3/ * Estonia: * ftp://redhat.linux.ee/pub/fedora/linux/core/3/ * http://redhat.linux.ee/pub/fedora/linux/core/3/ * Finland: * ftp://ftp.funet.fi/pub/mirrors/ftp.redhat.com/pub/fedora/linux/core/3/ * http://ftp.funet.fi/pub/mirrors/ftp.redhat.com/pub/fedora/linux/core/3/ * ftp://ftp.ipv6.funet.fi/pub/mirrors/ftp.redhat.com/pub/fedora/linux/core/3/ * http://ftp.ipv6.funet.fi/pub/mirrors/ftp.redhat.com/pub/fedora/linux/core/3/ * France: * ftp://fr2.rpmfind.net/linux/fedora/core/3/ * http://fr2.rpmfind.net/linux/fedora/core/3/ * ftp://ftp.lip6.fr/pub/linux/distributions/fedora/3/ * http://ftp.lip6.fr/pub/linux/distributions/fedora/3/ * ftp://ftp.proxad.net/mirrors/fedora.redhat.com/fedora/linux/core/3/ * http://ftp.crihan.fr/mirrors/fedora.redhat.com/fedora/linux/core/3 * ftp://ftp.crihan.fr/mirrors/fedora.redhat.com/fedora/linux/core/3 * rsync://ftp.crihan.fr/mirrors/fedora.redhat.com/fedora/linux/core/3 * Germany: * ftp://ftp.tu-chemnitz.de/pub/linux/fedora-core/3/ * http://wftp.tu-chemnitz.de/pub/linux/fedora-core/3/ * ftp://ftp-stud.fht-esslingen.de/Mirrors/fedora.redhat.com/linux/core/3/ * http://ftp-stud.fht-esslingen.de/Mirrors/fedora.redhat.com/linux/core/3/ * rsync://ftp-stud.fht-esslingen.de/fedora.redhat.com/linux/core/3 * http://download.atrpms.net/mirrors/fedoracore/3/ * ftp://ftp.informatik.uni-frankfurt.de/pub/linux/Mirror/ftp.redhat.com/fedor… * ftp://ftp.join.uni-muenster.de/pub/linux/distributions/fedora/linux/core/3/ * http://ftp.join.uni-muenster.de/pub/linux/distributions/fedora/linux/core/3/ * rsync: ftp.join.uni-muenster.de::fedora/linux/core/3/ * ftp://ftp.stw-bonn.de/pub/mirror/fedora/linux/core/ * Greece: * ftp://ftp.otenet.gr/pub/linux/fedora/linux/core/3/ * Ireland: * http://ftp.esat.net/mirrors/download.fedora.redhat.com/pub/fedora/linux/cor… * ftp://ftp.esat.net/mirrors/download.fedora.redhat.com/pub/fedora/linux/core… * rsync://ftp.esat.net/mirrors/download.fedora.redhat.com/pub/fedora/linux/co… * ftp://ftp.heanet.ie/pub/fedora/linux/core/3/ * http://ftp.heanet.ie/pub/fedora/linux/core/3/ * rsync://ftp.heanet.ie/pub/fedora/linux/core/3/ * Netherlands: * ftp://alviss.et.tudelft.nl/pub/fedora/core/3/ * ftp://ftp.nluug.nl/pub/os/Linux/distr/fedora/3/ * http://ftp.nluug.nl/pub/os/Linux/distr/fedora/3/ * rsync://ftp.nluug.nl/Fedora/3/ * ftp://ftp.surfnet.nl/pub/os/Linux/distr/fedora/3/ * http://ftp.surfnet.nl/pub/os/Linux/distr/fedora/3/ * rsync://ftp.surfnet.nl/Fedora/3/ * ftp://ftp.quicknet.nl/pub/Linux/download.fedora.redhat.com/3 * ftp://ftp.tudelft.nl/d1/Linux/download.fedora.redhat.com/3/ * Norway: * ftp://ftp.uninett.no/pub/linux/Fedora/core/3/ * rsync://ftp.uninett.no/fedora-linux-core/3/ * Poland: * ftp://sunsite.icm.edu.pl/pub/Linux/fedora/linux/core/3/ * http://sunsite.icm.edu.pl/pub/Linux/fedora/linux/core/3/ * rsync://sunsite.icm.edu.pl/pub/Linux/fedora/linux/core/3/ * ftp://ftp.wsisiz.edu.pl/pub/Linux/fedora/linux/core/3/ * ftp://ftp.ps.pl/pub/linux/fedora-core/3 * http://ftp.ps.pl/pub/linux/fedora-core/3 * Portugal: * ftp://ftp.di.fct.unl.pt/pub/linux/fedora/3/ * http://ftp.di.fct.unl.pt/pub/linux/fedora/3/ * Romania: * ftp://ftp.iasi.roedu.net/pub/mirrors/fedora.redhat.com/core/3/ * http://ftp.iasi.roedu.net/mirrors/fedora.redhat.com/core/3/ * rsync://ftp.iasi.roedu.net/fedora-core/core/3/ * ftp://ftp.lug.ro/fedora/linux/core/3 * http://ftp.lug.ro/fedora/linux/core/3 * Russia: * http://ftp.chg.ru/pub/Linux/fedora/linux/core/3/ * ftp://ftp.chg.ru/pub/Linux/fedora/linux/core/3/ * Spain: * ftp://ftp.udl.es/pub/fedora/linux/core/3/ * http://ftp.udl.es/pub/fedora/linux/core/3/ * rsync://ftp.udl.es/fedora/linux/core/3/ * ftp://ftp.cica.es/fedora/linux/core/3/ * http://sunsite.rediris.es/mirror/fedora.redhat/3 * ftp://ftp.rediris.es/mirror/fedora.redhat/3 * Slovenia: * http://mirrors.bevc.net/fedora/core/3/ * ftp://ftp.bevc.net/mirrors/fedora/core/3/ * Sweden: * ftp://ftp.chl.chalmers.se/pub/fedora/linux/core/3/ * United Kingdom: * http://www.mirrorservice.org/sites/download.fedora.redhat.com/pub/fedora/li… * ftp://ftp.mirrorservice.org/sites/download.fedora.redhat.com/pub/fedora/lin… * rsync://rsync.mirrorservice.org/sites/download.fedora.redhat.com/pub/fedora… * Asia/Pacific: * Australia: * http://planetmirror.com/pub/fedora/linux/core/3/ * ftp://ftp.planetmirror.com/pub/fedora/linux/core/3/ * rsync://rsync.planetmirror.com/fedora-linux-core/3/ * ftp://ftp.netcraft.com.au/pub/fedora/linux/core/3/ * China: * ftp://ftp.hostrino.com/pub/fedora/linux/core/3/ * http://ftp.hostrino.com/pub/fedora/linux/core/3/ * Japan: * ftp://ftp.riken.jp/Linux/fedora/core/3/ * http://ftp.riken.jp/Linux/fedora/core/3/ * rsync://ftp.riken.jp/fedora/core/3/ * ftp://download.sfc.wide.ad.jp/pub/Linux/Fedora/3/ * http://download.sfc.wide.ad.jp/pub/Linux/Fedora/3/ * ftp://ftp.kddialbs.jp/Linux/packages/fedora/core/3/ * http://ftp.kddialbs.jp/Linux/packages/fedora/core/3/ * rsync://ftp.kddilabs.jp/fedora/core/3/ * New Zealand: * ftp://ftp.wicks.co.nz/pub/linux/dist/fedora/3/ * Taiwan: * http://ftp.isu.edu.tw/pub/Linux/Fedora/linux/core/3 * ftp://ftp.isu.edu.tw/pub/Linux/Fedora/linux/core/3 More mirrors will come on line as time passes; please see http://fedora.redhat.com/download/mirrors.html for a list of mirrors that carry Fedora Core. Fedora Core 3 Release Notes Copyright (c) 2004 Red Hat, Inc. Permission is granted to copy, distribute, and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or any later version published by the Free Software Foundation; with no Invariant Sections, no Front-Cover Texts, and no Back-Cover Texts. A copy of the license is available at [1]http://www.gnu.org/licenses/fdl.html. This document may be copied and distributed in any medium, either commercially or non-commercially, provided that the GNU Free Documentation License (FDL), the copyright notices, and the license notice saying the GNU FDL applies to the document are reproduced in all copies, and that you add no other conditions whatsoever to those of the GNU FDL. Red Hat, Red Hat Network, the Red Hat "Shadow Man" logo, RPM, Maximum RPM, the RPM logo, Linux Library, PowerTools, Linux Undercover, RHmember, RHmember More, Rough Cuts, Rawhide and all Red Hat-based trademarks and logos are trademarks or registered trademarks of Red Hat, Inc. in the United States and other countries. The Fedora trademark is a trademark of Red Hat, Inc. in the United States and other countries. Linux is a registered trademark of Linus Torvalds. All other trademarks and copyrights referred to are the property of their respective owners. The GPG fingerprint of the "Fedora Project <fedora(a)redhat.com>" key is: CA B4 4B 99 6F 27 74 4E 86 12 7C DF B4 42 69 D0 4F 2A 6F D2 --------------------------------------------------------------------------- Introduction The Fedora Project is an openly-developed project designed by Red Hat, open for general participation, led by a meritocracy, and following a set of project objectives. The results from this project include Fedora Core, a complete, general-purpose operating system built exclusively from open source software. Note Fedora Core is not a supported product of Red Hat, Inc. For more information, refer to the Fedora Project overview later in this document. The following topics related to Fedora Core 3 are covered in this document: o Introduction (this section) o Hardware requirements o Overview of this release o Installation-related notes o Package-specific notes o Packages added/removed/deprecated o An overview of the Fedora Project Hardware Requirements The following information represents the minimum hardware requirements necessary to successfully install Fedora Core 3. Note The compatibility/availability of other hardware components (such as video and network cards) may be required for specific installation modes and/or post-installation usage. CPU Requirements This section lists the CPU specifications required by Fedora Core 3. Note The following CPU specifications are stated in terms of Intel processors. Other processors (notably, offerings from AMD, Cyrix, and VIA) that are compatible with and equivalent to the following Intel processors may also be used with Fedora Core. o Minimum: Pentium-class Fedora Core 3 is optimized for Pentium 4 CPUs, but also supports earlier CPUs (such as Pentium, Pentium Pro, Pentium II, Pentium III, and including AMD and VIA variants). This approach has been taken because Pentium-class optimizations actually result in reduced performance for non-Pentium-class processors, and Pentium 4 scheduling is sufficiently different (while making up the bulk of today's processors) to warrant this change. o Recommended for text-mode: 200 MHz Pentium-class or better o Recommended for graphical: 400 MHz Pentium II or better Hard Disk Space Requirements This section lists the disk space required to install Fedora Core 3. Note The disk space requirements listed below represent the disk space taken up by Fedora Core 3 after the installation is complete. However, additional disk space is required during the installation to support the installation environment. This additional disk space corresponds to the size of /Fedora/base/stage2.img (on CD-ROM 1) plus the size of the files in /var/lib/rpm on the installed system. In practical terms, this means that as little as an additional 90MB can be required for a minimal installation, while as much as an additional 175MB can be required for an "everything" installation. Also, keep in mind that additional space will be required for any user data, and at least 5% free space should be maintained for proper system operation. o Custom Installation (Minimal): 620MB o Server: 1.1GB o Personal Desktop: 2.3GB o Workstation: 3.0GB o Custom Installation (Everything): 6.9GB Memory Requirements This section lists the memory required to install Fedora Core 3. o Minimum for text-mode: 64MB o Minimum for graphical: 192MB o Recommended for graphical: 256MB Overview of This Release The following list includes brief summaries of some of the more significant aspects of Fedora Core 3: o Fedora Core 3 contains the following changes: o GCC 3.4 o GNOME 2.8 o KDE 3.3 o SELinux -- This includes a new "targeted" policy that monitors specific daemons with less intrusion than the strict policy in use before. This policy is enabled by default. For more information, refer to: [2]http://fedora.redhat.com/docs/selinux-faq/ o Indic language support o Firefox and Mozilla can be enabled with pango rendering support, which enables many text layout features, including the rendering of CTL (Complex Text Layout) such as Indic languages. To enable this, set the following environment variable when running Firefox or Mozilla: MOZ_ENABLE_PANGO=1 o Kernel and e2fsprogs support for online growing of ext3 file systems o Various desktop-related features, including, but not limited to: o Remote desktops using VNC ([3]http://www.redhat.com/archives/fedora-desktop-list/2004-June/msg00007.html) o Printing improvements ([4]http://mail.gnome.org/archives/desktop-devel-list/2004-June/msg00370.html) o Evolution 2.0 Note VMware WS 4.5.2 is known to work on Fedora Core 3 after the following workarounds are used: o You must upgrade the kernel modules and configuration using the unofficial vmware-any-any-* toolkit available from: [5]http://platan.vc.cvut.cz/ftp/pub/vmware/ o After vmware-config.pl is run and the VMware modules are loaded, the following command creates the /sys/class/* nodes needed for udev: cp -rp /dev/vm* /etc/udev/devices/ Installation-Related Notes This section outlines those issues that are related to Anaconda (the Fedora Core installation program) and installing Fedora Core 3 in general. Note If you intend to download the Fedora Core 3 DVD ISO image, keep in mind that not all file downloading tools can accommodate files larger than 2GB in size. For example, wget will exit with a File size limit exceeded error. The curl and ncftpget file downloading tools do not have this limitation, and can successfully download files larger than 2GB. Anaconda Notes o The Fedora Core installation program has the ability to test the integrity of the installation media. It works with the CD, DVD, hard drive ISO, and NFS ISO installation methods. Red Hat recommends that you test all installation media before starting the installation process, and before reporting any installation-related bugs (many of the bugs reported are actually due to improperly-burned CDs). To use this test, type linux mediacheck at the boot: prompt. o Memory testing may be performed prior to installing Fedora Core by entering memtest86 at the boot: prompt. This causes the Memtest86 standalone memory testing software to run. Memtest86 memory testing continues until the Esc key is pressed. NOTE: You must boot from CD-ROM 1 (or a rescue CD-ROM) in order to use this feature. o Fedora Core 3 supports graphical FTP and HTTP installations. However, due to the necessity of containing the installer image in RAM, only systems with more than 128MB of RAM (or systems booted from CD-ROM 1, which contains the installer image) can use the graphical installer. Systems with 128MB or less will continue to use the text-based installer. Installation-Related Issues o Certain hardware configurations (particularly those with LCD displays) may experience problems while starting the Fedora Core installation program. In these instances, restart the installation, and add the "nofb" option to the boot command line. NOTE: Chinese, Japanese, and Korean graphical installations started using the "nofb" option will start in English, and then switch to the appropriate language once the graphical phase of the installation process begins. o Some Sony VAIO(R) notebook systems may experience problems installing Fedora Core from CD-ROM. If this happens, restart the installation process and add the following option to the boot command line: pci=off ide1=0x180,0x386 This option allows the installation to proceed normally; any devices not detected due to the use of this option will be configured the first time Fedora Core is booted. o Serial mice are known to be inoperative during installation. However, there are indications that serial mice work properly in X after the installation has completed. Refer to bug 119474 for more information: [6]http://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=119474 o There have been issues observed when upgrading Red Hat Linux 7.<x>, 8.0, 9, and Fedora Core 1 systems running Ximian GNOME. The issue is caused by version overlap between the official Red Hat Linux RPMs (or the ones from the Fedora Project) and the Ximian RPMs. This configuration is not supported. You have several choices in resolving this issue: 1) You may remove Ximian GNOME from your system prior to upgrading to Fedora Core. 2) You may upgrade your system, and then immediately reinstall Ximian GNOME. 3) You may upgrade your system, and then immediately remove all remaining Ximian RPMs, replacing them with the corresponding Fedora Core RPMs. You must resolve the version overlap using one of the above choices. Failure to do so will result in an unstable GNOME configuration. Package-Specific Notes The following sections contain information regarding packages that have undergone significant changes for Fedora Core 3. For easier access, they are organized using the same groups used in Anaconda. Base This section contains information related to basic system components. openssh Fedora Core 3 contains OpenSSH 3.9, which includes strict permission and ownership checks for the ~/.ssh/config file. These checks mean that ssh will exit if this file does not have appropriate ownership and permissions. Therefore, make sure that ~/.ssh/config is owned by the owner of ~/, and that its permissions are set to mode 600. In addition, OpenSSH is no longer configured to request X11 forwarding by default when connecting to servers. To enable X11 forwarding, the -X or -Y option must be specified, or the ForwardX11 option must be enabled in the ~/.ssh/config file. The behavior of ssh clients that are invoked with the -X flag has changed. In OpenSSH 3.8 and later, X11 forwarding is performed in a way that applications run as untrusted clients by default. Previously, X11 forwarding was performed so that applications always ran as trusted clients. Some applications may not function properly when run as untrusted clients. To forward X11 so that applications are run as trusted clients, invoke ssh with the -Y flag instead of the -X flag, or set ForwardX11Trusted in the ~/.ssh/config file. Core This section contains the most elemental components of Fedora Core, including the kernel. e2fsprogs The ext2online utility has been added for online growing of existing ext3 file systems. Note It is important to keep in mind that ext2online does not grow the underlying block device itself -- there must be sufficient unused space already present on the device. The easiest way to ensure this is to use LVM volumes and to run lvresize or lvextend to extend the device. In addition, file systems must be specially prepared in order to be resized past a certain point. The preparation involves reserving a small amount of space into which on-disk tables can grow. For newly-created file systems, mke2fs reserves such space automatically; the space reserved is sufficient to grow the file system by a factor of 1000. The creation of this reserved space can be disabled by the following command: mke2fs -O ^resize_inode Future releases of Fedora Core will allow the creation of this reserved space on existing file systems. glibc o The version of glibc provided with Fedora Core 3 performs additional internal sanity checks to prevent and detect data corruption as early as possible. By default, should corruption be detected, a message similar to the following will be displayed on standard error (or logged via syslog if stderr is not open): *** glibc detected *** double free or corruption: 0x0937d008 *** By default, the program that generated this error will also be killed; however, this (and whether or not an error message is generated) can be controlled via the MALLOC_CHECK_ environment variable. The following settings are supported: o 0 -- Do not generate an error message, and do not kill the program o 1 -- Generate an error message, but do not kill the program o 2 -- Do not generate an error message, but kill the program o 3 -- Generate an error message and kill the program Note If MALLOC_CHECK_ is explicitly set a value other than 0, this causes glibc to perform more tests that are more extensive than the default, and may impact performance. Should you have a program from a third party ISV that triggers these corruption checks and displays a message, you should file a defect report with the application's vendor, since this indicates a serious bug. hotplug The location where hotplug expects firmware to be loaded into (for example, firmware for Cardbus cards) has changed from /usr/lib/hotplug/firmware to /lib/firmware. Existing firmware files must be moved into the new directory. kernel o In the past, the process of updating the kernel did not change the default kernel in the system's boot loader configuration. Fedora Core 3 changes this behavior to set newly-installed kernels as the default. This behavior applies to all installation methods (including rpm -i). This behavior is controlled by two lines in the /etc/sysconfig/kernel file: o UPGRADEDEFAULT -- Controls whether new kernels will be booted by default (default value: yes) o DEFAULTKERNEL -- kernel RPMs whose names match this value will be booted by default (default value: depends on hardware configuration) o In order to eliminate the redundancy inherent in providing a separate package for the kernel source code when that source code already exists in the kernel's .src.rpm file, Fedora Core 3 no longer includes the kernel-source package. Users that require access to the kernel sources can find them in the kernel .src.rpm file. To create an exploded source tree from this file, perform the following steps (note that <version> refers to the version specification for your currently-running kernel): 1. Obtain the kernel-<version>.src.rpm file from one of the following sources: o The SRPMS directory on the appropriate "SRPMS" CD iso image o The FTP site where you got the kernel package o By running the following command: up2date --get-source kernel 2. Install kernel-<version>.src.rpm (given the default RPM configuration, the files this package contains will be written to /usr/src/redhat/) 3. Change directory to /usr/src/redhat/SPECS/, and issue the following command: rpmbuild -bp --target=<arch> kernel.spec (Where <arch> is the desired target architecture.) On a default RPM configuration, the kernel tree will be located in /usr/src/redhat/BUILD/. 4. In resulting tree, the configurations for the specific kernels shipped in Fedora Core 3 are in the /configs/ directory. For example, the i686 SMP configuration file is named /configs/kernel-<version>-i686-smp.config. Issue the following command to place the desired configuration file in the proper place for building: cp <desired-file> ./.config 5. Issue the following command: make oldconfig You can then proceed as usual. Note An exploded source tree is not required to build kernel modules against the currently in-use kernel. For example, to build the foo.ko module, create the following file (named Makefile) in the directory containing the foo.c file: obj-m := foo.o KDIR := /lib/modules/$(shell uname -r)/build PWD := $(shell pwd) default: $(MAKE) -C $(KDIR) SUBDIRS=$(PWD) modules Issue the make command to build the foo.ko module. o I[2]O SCSI RAID adapters from manufacturers such as Adaptec now use the i2o_block driver, rather than the dpt_i2o driver used by Fedora Core 1 and earlier distributions. Be aware that block devices used by the i2o_block driver are /dev/i2o/hd* rather than the /dev/sd* SCSI devices. This may be problematic for those upgrading from older distributions that used the dpt_i2o driver. Therefore, after an upgrade to Fedora Core 3, you may need to boot using a rescue disk and edit your /etc/fstab file to use the new devices. For more information about the new I[2]O device layer and Fedora Core-specific notes, visit the I[2]O homepage: [7]http://i2o.shadowconnect.com/ Language Support This section includes information related to the support of various languages under Fedora Core. iiimf o The default Input Method (IM) for Chinese (Simplified and Traditional), Japanese, and Korean has been changed to IIIMF -- the Internet/Intranet Input Method Framework. IIIMF is supported as a native GTK2 IM module, and also through XIM using the httx client. IIIMF supports the use of multiple Language Engines (LEs) at the same time; using the GNOME Input Method Language Engine Tool (GIMLET -- an applet) it is possible to switch between LEs of different languages inside GTK2 applications. IIIMF currently defaults to using Ctrl-Space or Shift-Space for toggling the input method on and off (Emacs users can use Ctrl-@ instead of Ctrl-Space to set the mark.) Depending on your selection at the language support screen during installation, one or more IIIMF language engines may be installed. The IIIMF server package (iiimf-server) will also be installed if a language engine has been selected. The language to language engine (LE) package mappings are as follows: o ja_JP -- iiimf-le-canna o zh_CN -- iiimf-le-chinput o zh_TW -- iiimf-le-xcin o ko_KR -- iiimf-le-hangul o {bn,gu,pa,ta,hi}_IN -- iiimf-le-unit Accordingly, input via IIIMF will be enabled if you have chosen one of the following as your default locale: o ja_JP o zh_CN o zh_TW o ko_KR o {bn,gu,pa,ta,hi}_IN To aid your use of IIIMF, if you have selected one of the above locales and you are using the GNOME Desktop, when you first login the GIMLET utility (part of the iiimf-gnome-im-switcher package) will automatically be added to your panel. GIMLET is a utility for switching between the different LEs that are installed on your system. Using a different language engine allows you to enter text in different languages. Alternatively you may add GIMLET manually to your panel by right clicking on the panel and selecting: Add to Panel -> GIMLET Should you wish to switch between IIIMF or the legacy input method framework XIM, you can use the system-switch-im application. After changing the input method framework your changes will be reflected when you next start the X Window System. Mail Server This section contains information related to the mail transport agents included with Fedora Core. mailman Earlier mailman RPMs installed all files under the /var/mailman/ directory. Unfortunately, this did not conform to the Filesystem Hierarchy Standard (FHS) and also created security violations when SELinux was enabled. If you previously had mailman installed and had edited files in /var/mailman/ (such as mm_cfg.py) you must move those changes to their new location, as documented in the following file: /usr/share/doc/mailman-*/INSTALL.REDHAT sendmail o By default, the Sendmail mail transport agent (MTA) does not accept network connections from any host other than the local computer. If you want to configure Sendmail as a server for other clients, you must edit /etc/mail/sendmail.mc and change the DAEMON_OPTIONS line to also listen on network devices (or comment out this option entirely using the dnl comment delimiter). You must then regenerate /etc/mail/sendmail.cf by running the following command (as root): make -C /etc/mail Note that you must have the sendmail-cf package installed for this to work. Server Configuration Tools This section contains information related to various server configuration tools. system-config-securitylevel The firewall constructed by the system-config-securitylevel configuration tool now allows CUPS and Multicast DNS (mDNS) browsing. Note that, at the present time, these services cannot be disabled by system-config-securitylevel. Sound and Video This section contains information related to multimedia applications. k3b Past users of the CD/DVD burning application k3b may notice that the program k3bsetup is missing. This is because k3bsetup is not necessary under Fedora Core 3. Web Server This section contains information related to Web-related tools. crypto-utils The certwatch(1) tool has been added to the crypto-utils package. This tool is used to send warning mail to root when any configured SSL certificates have expired or are approaching the expiration date. By default, the tool checks any certificates that are enabled in the mod_ssl configuration. httpd By default, the httpd daemon is now started using the C locale, rather than using the configured system locale setting. This behavior can be changed by setting the HTTPD_LANG variable in the /etc/sysconfig/httpd file. php The gd, mbstring, and ncurses extensions have been moved to the php-gd, php-mbstring, and php-ncurses packages, respectively. Note that you will need to install these packages manually (if required) when upgrading from an earlier release. Windows File Server This section contains information related to Samba, software that makes it possible to share files between Linux and Windows systems. samba Browsing of Windows shares (also known as SMB browsing) fails on Fedora Core 3 systems that have the standard firewall configured. This is most easily noticed in the failure of Nautilus to display shares. The failure is due to the firewall disrupting the broadcast mode of SMB browsing, which is Samba's default setting. There are two workarounds: o Configure a WINS server on the network, and set the "wins server" option in smb.conf to the address of the WINS server. o Disable the firewall Warning Depending on your system and network configurations, disabling the firewall can greatly increase the chance of your system being attacked and compromised. Make sure you fully understand the risks before undertaking this step. For additional information, refer to the following bug report: [8]https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=133478 X Window System This section contains information related to the X Window System implementation provided with Fedora Core. xorg-x11 o Users new to the X.org X11 implementation should take note of a few differences between it and the XFree86.org X11 implementation which shipped in previous Red Hat operating systems. In particular, the names of some files have changed: X Server Binary: o XFree86 X11: XFree86 o X.org X11: Xorg X Server Configuration File: o XFree86 X11: /etc/X11/XF86Config o X.org X11: /etc/X11/xorg.conf X Server Log File o XFree86 X11: /var/log/XFree86.$DISPLAY.log o X.org X11: /var/log/Xorg.$DISPLAY.log When configuring or troubleshooting your X server configuration, be sure that you are using the correct files. o There has been some confusion regarding font-related issues under the X Window System in recent versions of Fedora Core (and versions of Red Hat Linux before it.) At the present time, there are two font subsystems, each with different characteristics: - The original (15+ year old) subsystem is referred to as the "core X font subsystem". Fonts rendered by this subsystem are not anti-aliased, are handled by the X server, and have names like: -misc-fixed-medium-r-normal--10-100-75-75-c-60-iso8859-1 The newer font subsystem is known as "fontconfig", and allows applications direct access to the font files. Fontconfig is often used along with the "Xft" library, which allows applications to render fontconfig fonts to the screen with antialiasing. Fontconfig uses more human-friendly names like: Luxi Sans-10 Over time, fontconfig/Xft will replace the core X font subsystem. At the present time, applications using the Qt 3 or GTK 2 toolkits (which would include KDE and GNOME applications) use the fontconfig and Xft font subsystem; most everything else uses the core X fonts. In the future, Fedora Core may support only fontconfig/Xft in place of the XFS font server as the default local font access method. NOTE: An exception to the font subsystem usage outlined above is OpenOffice.org (which uses its own font rendering technology). If you wish to add new fonts to your Fedora Core 3 system, you must be aware that the steps necessary depend on which font subsystem is to use the new fonts. For the core X font subsystem, you must: 1. Create the /usr/share/fonts/local/ directory (if it doesn't already exist): mkdir /usr/share/fonts/local/ 2. Copy the new font file into /usr/share/fonts/local/ 3. Update the font information by issuing the following commands (note that, due to formatting restrictions, the following commands may appear on more than one line; in use, each command should be entered on a single line): ttmkfdir -d /usr/share/fonts/local/ -o /usr/share/fonts/local/fonts.scale mkfontdir /usr/share/fonts/local/ 4. If you had to create /usr/share/fonts/local/, you must then add it to the X font server (xfs) path: chkfontpath --add /usr/share/fonts/local/ Adding new fonts to the fontconfig font subsystem is more straightforward; the new font file only needs to be copied into the /usr/share/fonts/ directory (individual users can modify their personal font configuration by copying the font file into the ~/.fonts/ directory). After the new font has been copied, use fc-cache to update the font information cache: fc-cache <directory> (Where <directory> would be either the /usr/share/fonts/ or ~/.fonts/ directories.) Individual users may also install fonts graphically, by browsing fonts:/// in Nautilus, and dragging the new font files there. NOTE: If the font filename ends with ".gz", it has been compressed with gzip, and must be decompressed (with the gunzip command) before the fontconfig font subsystem can use the font. o Due to the transition to the new font system based on fontconfig/Xft, GTK+ 1.2 applications are not affected by any changes made via the Font Preferences dialog. For these applications, a font can be configured by adding the following lines to the file ~/.gtkrc.mine: style "user-font" { fontset = "<font-specification>" } widget_class "*" style "user-font" (Where <font-specification> represents a font specification in the style used by traditional X applications, such as "-adobe-helvetica-medium-r-normal--*-120-*-*-*-*-*-*".) Miscellaneous Notes This section contains information related to packages that do not fit in any of the proceeding categories. compat-db C++ and TCL bindings are no longer contained in the compat-db package. Applications requiring these bindings must be ported to the currently-shipping DB library. nscd The nscd name service cache daemon may now maintain a persistent cache across restarts or system reboots. Each database (user, group, and host, respectively) can be made selected to be persistent by setting the appropriate line in /etc/nscd.conf to "yes". Entries are not removed from the cache until they are proven to be no longer of interest. All entries whose time-to-live expires but are otherwise interesting are automatically reloaded, which helps in situations where the directory and name services become temporarily unavailable. The nscd name service daemon is also able to communicate faster with client programs. This feature must be enabled explicitly by setting the "shared" entry for the appropriate database in /etc/nscd.conf to "yes". udev Fedora Core 3 has switched from a static /dev/ directory to one that is dynamically managed via udev. This allows device nodes to be created on demand as drivers are loaded. For more information on udev, refer to the udev(8) man page and the following link: [9]http://people.redhat.com/~harald/udev.html Additional rules for udev should be placed in a separate file in the /etc/udev/rules.d/ directory. Additional permission rules for udev should be placed in a separate file in the /etc/udev/permissions.d/ directory. Systems upgraded to Fedora Core 3 using Anaconda will automatically be reconfigured to use udev. However (although NOT recommended) it is possible to perform a "live" upgrade to udev using the following steps: 1. Ensure that you are running a 2.6 kernel 2. Ensure that /sys/ is mounted 3. Install the initscripts RPM supplied with Fedora Core 3 4. Install the new udev RPM supplied with Fedora Core 3 5. Execute /sbin/start_udev 6. Install the new mkinitrd RPM supplied with Fedora Core 3 7. Perform one of the following steps: . Install the new kernel RPM supplied with Fedora Core 3 OR: . Re-run mkinitrd for your existing kernel(s) Warning Improperly performing these steps can result in a system configuration that will not boot properly. Packages Added/Removed/Deprecated This section contains lists of packages that fit into the following categories: o Packages that have been added to Fedora Core 3 o Packages that have been removed from Fedora Core 3 o Packages that have been deprecated, and may be removed from a future release of Fedora Core Packages Added The following packages have been added to Fedora Core 3: o HelixPlayer o NetworkManager o NetworkManager-gnome o Pyrex o aiksaurus o aiksaurus-devel o aiksaurus-gtk o aiksaurus-gtk-devel o arptables_jf o aspell-af o aspell-bg o aspell-br o aspell-ca o aspell-cs o aspell-cy o aspell-el o aspell-fo o aspell-ga o aspell-gd o aspell-gl o aspell-hr o aspell-ia o aspell-id o aspell-it o aspell-pl o audit o authd o bluez-utils-cups o bzflag o compat-openldap o crash o createrepo o crypto-utils o cscope o cyrus-sasl-ntlm o cyrus-sasl-sql o dasher o db4-java o dbus-python o dhcpv6 o dhcpv6_client o diskdumputils o dmraid o docbook-simple o docbook-slides o ecj o epiphany-devel o evolution-connector o evolution-data-server o evolution-data-server-devel o evolution-webcal o fedora-release o firefox o fonts-xorg-100dpi o fonts-xorg-75dpi o fonts-xorg-ISO8859-14-100dpi o fonts-xorg-ISO8859-14-75dpi o fonts-xorg-ISO8859-15-100dpi o fonts-xorg-ISO8859-15-75dpi o fonts-xorg-ISO8859-2-100dpi o fonts-xorg-ISO8859-2-75dpi o fonts-xorg-ISO8859-9-100dpi o fonts-xorg-ISO8859-9-75dpi o fonts-xorg-base o fonts-xorg-cyrillic o fonts-xorg-syriac o fonts-xorg-truetype o gamin o gamin-devel o gcc4 o gcc4-c++ o gcc4-gfortran o gda-mysql o gda-odbc o gda-postgres o gettext-devel o gnome-keyring-manager o gnome-nettool o gnome-volume-manager o gnuplot-emacs o gnutls o gnutls-devel o gok-devel o hal o hal-cups-utils o hal-devel o hal-gnome o howl o howl-devel o howl-libs o httpd-suexec o iiimf-gnome-im-switcher o iiimf-le-chinput o iiimf-le-sun-thai o iiimf-libs o iiimf-libs-devel o java-1.4.2-gcj-compat o java-1.4.2-gcj-compat-devel o jpackage-utils o katana o katana-build o kde-i18n-Bulgarian o kdeaddons-xmms o kdenetwork-nowlistening o kdewebdev o kdewebdev-devel o kinput2 o krb5-auth-dialog o libbtctl-devel o libgda o libgda-devel o libgfortran o libgnomedb o libgnomedb-devel o libidn o libidn-devel o libmudflap o libmudflap-devel o libsepol o libsepol-devel o libsilc o libsilc-devel o libsilc-doc o libtheora o libtheora-devel o libwmf o libwmf-devel o linuxwacom o linuxwacom-devel o mikmod-devel o mod_authz_ldap o module-init-tools o nautilus-cd-burner-devel o net-snmp-libs o newt-perl o nptl-devel (i386) o numactl o octave-devel o openldap-servers-sql o openoffice.org-kde o openswan o pam_ccreds o pam_passwdqc o php-gd o php-mbstring o php-ncurses o python-ldap o qt-config o rpm-libs o selinux-policy-strict o selinux-policy-strict-sources o selinux-policy-targeted o selinux-policy-targeted-sources o sg3_utils o synaptics o sysfsutils o sysfsutils-devel o system-switch-im o theora-tools o thunderbird o tn5250 o tn5250-devel o totem o ttfonts-bn o ttfonts-gu o ttfonts-hi o ttfonts-pa o ttfonts-ta o valgrind o valgrind-callgrind o vino o xfce4-iconbox o xfce4-systray o xffm-icons o xfprint o xorg-x11-Xdmx o xorg-x11-deprecated-libs o xorg-x11-deprecated-libs-devel Packages Removed The following packages have been removed from Fedora Core 3: o FreeWnn-common o Gtk-Perl o Wnn6-SDK o Wnn6-SDK-devel o ac-archive o anaconda-images o ant o ant-core o ant-devel o ant-optional o aspell-pt_BR o bcel o bcel-devel o bluez-pan o bluez-sdp o bluez-sdp-devel o chromium o commons-beanutils o commons-beanutils-devel o commons-collections o commons-collections-devel o commons-dbcp o commons-dbcp-devel o commons-digester o commons-digester-devel o commons-fileupload o commons-fileupload-devel o commons-logging o commons-logging-devel o commons-modeler o commons-modeler-devel o commons-pool o commons-pool-devel o comps o cup o cup-devel o dev o devlabel o dvdrecord o fam o fam-devel o fedora-release o gcc34 o gcc34-c++ o gcc34-java o glade o gqview o gtkam o gtkam-gimp o gtkglarea o hwcrypto o iiimf-client-lib o iiimf-client-lib-devel o iiimf-le-inpinyin o iiimf-le-newpy o iiimf-protocol-lib o iiimf-protocol-lib-devel o imlib-cfgeditor o iscsi o jaf o jaf-devel o jakarta-regexp o jakarta-regexp-devel o javamail o javamail-devel o junit o junit-devel o kde-i18n-Korean o kde-i18n-Lithuanian o kernel-source o kinput2-canna-wnn6 o libgcj34 o libgcj34-devel o libgnomeprint o libgnomeprint-devel o libgnomeprintui o libgnomeprintui-devel o libole2 o libole2-devel o librep o librep-devel o libstdc++34 o libstdc++34-devel o licq o licq-gnome o licq-kde o licq-qt o licq-text o linc o linc-devel o lvm o magicdev o mod_jk2 o modutils o mx4j o mx4j-devel o mx4j-tools o mysql-jdbc o mysql-jdbc-tomcat o ncurses-c++-devel o njamd o pidentd o pilot-link095-compat o policy o policy-sources o policy-strict-sources o printman o python-optik o quanta o quanta-devel o raidtools o redhat-java-rpm-scripts o rep-gtk o sawfish o servletapi o servletapi-devel o shapecfg o struts o struts-webapps o system-config-proc o tomcat o tomcat-devel o tomcat-libs o tomcat-test o unarj o xalan-j o xalan-j-devel o xalan-j-xsltc o xerces-j o xerces-j-devel o xffm-icons o xorg-x11-100dpi-fonts o xorg-x11-75dpi-fonts o xorg-x11-ISO8859-14-100dpi-fonts o xorg-x11-ISO8859-14-75dpi-fonts o xorg-x11-ISO8859-15-100dpi-fonts o xorg-x11-ISO8859-15-75dpi-fonts o xorg-x11-ISO8859-2-100dpi-fonts o xorg-x11-ISO8859-2-75dpi-fonts o xorg-x11-ISO8859-9-100dpi-fonts o xorg-x11-ISO8859-9-75dpi-fonts o xorg-x11-base-fonts o xorg-x11-cyrillic-fonts o xorg-x11-libs-data o xorg-x11-syriac-fonts o xorg-x11-truetype-fonts Packages Deprecated The following packages have been deprecated, and may be removed from a future release of Fedora Core: o dbskkd-cdb -- Only used by deprecated package skkinput o FreeWnn -- Only used by deprecated package kinput2-canna-wnn6 o lilo -- GRUB is the recommended bootloader o miniChinput -- IIIMF is the recommended input method o nabi -- IIIMF is the recommended input method o ncpfs -- No longer part of Fedora Core profile o skkinput -- IIIMF is the recommended input method o xcin -- IIIMF is the recommended input method An Overview of the Fedora Project The goal of the Fedora Project is to work with the Linux community to build a complete, general-purpose operating system exclusively from open source software. Development will be done in a public forum. The project will produce time-based releases of Fedora Core about 2-3 times a year, with a public release schedule. The Red Hat engineering team will continue to participate in building Fedora Core and will invite and encourage more outside participation than was possible in the past. By using this more open process, we hope to provide an operating system more in line with the ideals of free software and more appealing to the open source community. For more information, refer to the Fedora Project website: [10]http://fedora.redhat.com/ In addition to the website, the following mailing lists are available: o fedora-list(a)redhat.com -- For users of Fedora Core releases o fedora-test-list(a)redhat.com -- For testers of Fedora Core test releases o fedora-devel-list(a)redhat.com -- For developers, developers, developers o fedora-docs-list(a)redhat.com -- For participants of the docs project To subscribe to any of these lists, send an email with the word "subscribe" in the subject to <listname>-request (where <listname> is one of the above list names.) NOTE: If you have subscribed in the past to rhl-list, rhl-beta-list, rhl-devel-list, or rhl-docs-list, your subscriptions have been retained. The Fedora Project also includes an IRC (Internet Relay Chat) channel. IRC is a real-time, text-based form of communication. With it, you can have conversations with multiple people in an open channel or chat with someone privately one-on-one. To talk with other Fedora Project participants via IRC, access freenode IRC network. Initially, you can use irc.freenode.net as the IRC server, although you may decide to select a server that is geographically closer to you. Refer to the freenode website ([11]http://www.freenode.net/) for more information. Fedora Project participants frequent the #fedora channel, while Fedora Project developers can often be found on the #fedora-devel channel. Some of the larger projects may have their own channels as well; this information can be found on the project pages. NOTE: Red Hat has no control over the Fedora IRC channels or their content. ( x86 ) References Visible links 1. http://www.gnu.org/licenses/fdl.html 2. http://fedora.redhat.com/docs/selinux-faq/ 3. http://www.redhat.com/archives/fedora-desktop-list/2004-June/msg00007.html 4. http://mail.gnome.org/archives/desktop-devel-list/2004-June/msg00370.html 5. http://platan.vc.cvut.cz/ftp/pub/vmware/ 6. http://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=119474 7. http://i2o.shadowconnect.com/ 8. https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=133478 9. http://people.redhat.com/~harald/udev.html 10. http://fedora.redhat.com/ 11. http://www.freenode.net/ Fedora Core 3 Release Notes Copyright (c) 2004 Red Hat, Inc. Permission is granted to copy, distribute, and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or any later version published by the Free Software Foundation; with no Invariant Sections, no Front-Cover Texts, and no Back-Cover Texts. A copy of the license is available at [1]http://www.gnu.org/licenses/fdl.html. This document may be copied and distributed in any medium, either commercially or non-commercially, provided that the GNU Free Documentation License (FDL), the copyright notices, and the license notice saying the GNU FDL applies to the document are reproduced in all copies, and that you add no other conditions whatsoever to those of the GNU FDL. Red Hat, Red Hat Network, the Red Hat "Shadow Man" logo, RPM, Maximum RPM, the RPM logo, Linux Library, PowerTools, Linux Undercover, RHmember, RHmember More, Rough Cuts, Rawhide and all Red Hat-based trademarks and logos are trademarks or registered trademarks of Red Hat, Inc. in the United States and other countries. The Fedora trademark is a trademark of Red Hat, Inc. in the United States and other countries. Linux is a registered trademark of Linus Torvalds. All other trademarks and copyrights referred to are the property of their respective owners. The GPG fingerprint of the "Fedora Project <fedora(a)redhat.com>" key is: CA B4 4B 99 6F 27 74 4E 86 12 7C DF B4 42 69 D0 4F 2A 6F D2 --------------------------------------------------------------------------- Introduction The Fedora Project is an openly-developed project designed by Red Hat, open for general participation, led by a meritocracy, and following a set of project objectives. The results from this project include Fedora Core, a complete, general-purpose operating system built exclusively from open source software. Note Fedora Core is not a supported product of Red Hat, Inc. For more information, refer to the Fedora Project overview later in this document. The following topics related to Fedora Core 3 are covered in this document: o Introduction (this section) o Hardware requirements o Overview of this release o Installation-related notes o Package-specific notes o Packages added/removed/deprecated o An overview of the Fedora Project Hardware Requirements The following information represents the minimum hardware requirements necessary to successfully install Fedora Core 3. Note The compatibility/availability of other hardware components (such as video and network cards) may be required for specific installation modes and/or post-installation usage. CPU Requirements This section lists the CPU specifications required by Fedora Core 3. o AMD64 processors (both Athlon64 and Opteron) o Intel processors with Intel(R) Extended Memory 64 Technology (Intel(R) EM64T) Hard Disk Space Requirements This section lists the disk space required to install Fedora Core 3. Note The disk space requirements listed below represent the disk space taken up by Fedora Core 3 after the installation is complete. However, additional disk space is required during the installation to support the installation environment. This additional disk space corresponds to the size of /Fedora/base/stage2.img (on CD-ROM 1) plus the size of the files in /var/lib/rpm on the installed system. In practical terms, this means that as little as an additional 90MB can be required for a minimal installation, while as much as an additional 175MB can be required for an "everything" installation. Also, keep in mind that additional space will be required for any user data, and at least 5% free space should be maintained for proper system operation. o Custom Installation (Minimal): 900MB o Server: 1.5GB o Personal Desktop: 2.7GB o Workstation: 3.4GB o Custom Installation: (Everything) 7.5GB Memory Requirements This section lists the memory required to install Fedora Core 3. o Minimum for text-mode: 128MB o Minimum for graphical: 256MB o Recommended for graphical: 512MB Overview of This Release The following list includes brief summaries of some of the more significant aspects of Fedora Core 3: o Fedora Core 3 contains the following changes: o GCC 3.4 o GNOME 2.8 o KDE 3.3 o SELinux -- This includes a new "targeted" policy that monitors specific daemons with less intrusion than the strict policy in use before. This policy is enabled by default. For more information, refer to: [2]http://fedora.redhat.com/docs/selinux-faq/ o Indic language support o Firefox and Mozilla can be enabled with pango rendering support, which enables many text layout features, including the rendering of CTL (Complex Text Layout) such as Indic languages. To enable this, set the following environment variable when running Firefox or Mozilla: MOZ_ENABLE_PANGO=1 o Kernel and e2fsprogs support for online growing of ext3 file systems o Various desktop-related features, including, but not limited to: o Remote desktops using VNC ([3]http://www.redhat.com/archives/fedora-desktop-list/2004-June/msg00007.html) o Printing improvements ([4]http://mail.gnome.org/archives/desktop-devel-list/2004-June/msg00370.html) o Evolution 2.0 Note VMware WS 4.5.2 is known to work on Fedora Core 3 after the following workarounds are used: o You must upgrade the kernel modules and configuration using the unofficial vmware-any-any-* toolkit available from: [5]http://platan.vc.cvut.cz/ftp/pub/vmware/ o After vmware-config.pl is run and the VMware modules are loaded, the following command creates the /sys/class/* nodes needed for udev: cp -rp /dev/vm* /etc/udev/devices/ Installation-Related Notes This section outlines those issues that are related to Anaconda (the Fedora Core installation program) and installing Fedora Core 3 in general. Note If you intend to download the Fedora Core 3 DVD ISO image, keep in mind that not all file downloading tools can accommodate files larger than 2GB in size. For example, wget will exit with a File size limit exceeded error. The curl and ncftpget file downloading tools do not have this limitation, and can successfully download files larger than 2GB. Anaconda Notes o The Fedora Core installation program has the ability to test the integrity of the installation media. It works with the CD, DVD, hard drive ISO, and NFS ISO installation methods. Red Hat recommends that you test all installation media before starting the installation process, and before reporting any installation-related bugs (many of the bugs reported are actually due to improperly-burned CDs). To use this test, type linux mediacheck at the boot: prompt. o Fedora Core 3 supports graphical FTP and HTTP installations. However, due to the necessity of containing the installer image in RAM, only systems with more than 128MB of RAM (or systems booted from CD-ROM 1, which contains the installer image) can use the graphical installer. Systems with 128MB or less will continue to use the text-based installer. Installation-Related Issues o Certain hardware configurations (particularly those with LCD displays) may experience problems while starting the Fedora Core installation program. In these instances, restart the installation, and add the "nofb" option to the boot command line. NOTE: Chinese, Japanese, and Korean graphical installations started using the "nofb" option will start in English, and then switch to the appropriate language once the graphical phase of the installation process begins. o Serial mice are known to be inoperative during installation. However, there are indications that serial mice work properly in X after the installation has completed. Refer to bug 119474 for more information: [6]http://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=119474 Package-Specific Notes The following sections contain information regarding packages that have undergone significant changes for Fedora Core 3. For easier access, they are organized using the same groups used in Anaconda. Base This section contains information related to basic system components. openssh Fedora Core 3 contains OpenSSH 3.9, which includes strict permission and ownership checks for the ~/.ssh/config file. These checks mean that ssh will exit if this file does not have appropriate ownership and permissions. Therefore, make sure that ~/.ssh/config is owned by the owner of ~/, and that its permissions are set to mode 600. In addition, OpenSSH is no longer configured to request X11 forwarding by default when connecting to servers. To enable X11 forwarding, the -X or -Y option must be specified, or the ForwardX11 option must be enabled in the ~/.ssh/config file. The behavior of ssh clients that are invoked with the -X flag has changed. In OpenSSH 3.8 and later, X11 forwarding is performed in a way that applications run as untrusted clients by default. Previously, X11 forwarding was performed so that applications always ran as trusted clients. Some applications may not function properly when run as untrusted clients. To forward X11 so that applications are run as trusted clients, invoke ssh with the -Y flag instead of the -X flag, or set ForwardX11Trusted in the ~/.ssh/config file. Core This section contains the most elemental components of Fedora Core, including the kernel. e2fsprogs The ext2online utility has been added for online growing of existing ext3 file systems. Note It is important to keep in mind that ext2online does not grow the underlying block device itself -- there must be sufficient unused space already present on the device. The easiest way to ensure this is to use LVM volumes and to run lvresize or lvextend to extend the device. In addition, file systems must be specially prepared in order to be resized past a certain point. The preparation involves reserving a small amount of space into which on-disk tables can grow. For newly-created file systems, mke2fs reserves such space automatically; the space reserved is sufficient to grow the file system by a factor of 1000. The creation of this reserved space can be disabled by the following command: mke2fs -O ^resize_inode Future releases of Fedora Core will allow the creation of this reserved space on existing file systems. glibc o The version of glibc provided with Fedora Core 3 performs additional internal sanity checks to prevent and detect data corruption as early as possible. By default, should corruption be detected, a message similar to the following will be displayed on standard error (or logged via syslog if stderr is not open): *** glibc detected *** double free or corruption: 0x0937d008 *** By default, the program that generated this error will also be killed; however, this (and whether or not an error message is generated) can be controlled via the MALLOC_CHECK_ environment variable. The following settings are supported: o 0 -- Do not generate an error message, and do not kill the program o 1 -- Generate an error message, but do not kill the program o 2 -- Do not generate an error message, but kill the program o 3 -- Generate an error message and kill the program Note If MALLOC_CHECK_ is explicitly set a value other than 0, this causes glibc to perform more tests that are more extensive than the default, and may impact performance. Should you have a program from a third party ISV that triggers these corruption checks and displays a message, you should file a defect report with the application's vendor, since this indicates a serious bug. hotplug The location where hotplug expects firmware to be loaded into (for example, firmware for Cardbus cards) has changed from /usr/lib/hotplug/firmware to /lib/firmware. Existing firmware files must be moved into the new directory. kernel o In the past, the process of updating the kernel did not change the default kernel in the system's boot loader configuration. Fedora Core 3 changes this behavior to set newly-installed kernels as the default. This behavior applies to all installation methods (including rpm -i). This behavior is controlled by two lines in the /etc/sysconfig/kernel file: o UPGRADEDEFAULT -- Controls whether new kernels will be booted by default (default value: yes) o DEFAULTKERNEL -- kernel RPMs whose names match this value will be booted by default (default value: depends on hardware configuration) o In order to eliminate the redundancy inherent in providing a separate package for the kernel source code when that source code already exists in the kernel's .src.rpm file, Fedora Core 3 no longer includes the kernel-source package. Users that require access to the kernel sources can find them in the kernel .src.rpm file. To create an exploded source tree from this file, perform the following steps (note that <version> refers to the version specification for your currently-running kernel): 1. Obtain the kernel-<version>.src.rpm file from one of the following sources: o The SRPMS directory on the appropriate "SRPMS" CD iso image o The FTP site where you got the kernel package o By running the following command: up2date --get-source kernel 2. Install kernel-<version>.src.rpm (given the default RPM configuration, the files this package contains will be written to /usr/src/redhat/) 3. Change directory to /usr/src/redhat/SPECS/, and issue the following command: rpmbuild -bp --target=<arch> kernel.spec (Where <arch> is the desired target architecture.) On a default RPM configuration, the kernel tree will be located in /usr/src/redhat/BUILD/. 4. In resulting tree, the configurations for the specific kernels shipped in Fedora Core 3 are in the /configs/ directory. For example, the i686 SMP configuration file is named /configs/kernel-<version>-i686-smp.config. Issue the following command to place the desired configuration file in the proper place for building: cp <desired-file> ./.config 5. Issue the following command: make oldconfig You can then proceed as usual. Note An exploded source tree is not required to build kernel modules against the currently in-use kernel. For example, to build the foo.ko module, create the following file (named Makefile) in the directory containing the foo.c file: obj-m := foo.o KDIR := /lib/modules/$(shell uname -r)/build PWD := $(shell pwd) default: $(MAKE) -C $(KDIR) SUBDIRS=$(PWD) modules Issue the make command to build the foo.ko module. o I[2]O SCSI RAID adapters from manufacturers such as Adaptec now use the i2o_block driver, rather than the dpt_i2o driver used by Fedora Core 1 and earlier distributions. Be aware that block devices used by the i2o_block driver are /dev/i2o/hd* rather than the /dev/sd* SCSI devices. This may be problematic for those upgrading from older distributions that used the dpt_i2o driver. Therefore, after an upgrade to Fedora Core 3, you may need to boot using a rescue disk and edit your /etc/fstab file to use the new devices. For more information about the new I[2]O device layer and Fedora Core-specific notes, visit the I[2]O homepage: [7]http://i2o.shadowconnect.com/ Language Support This section includes information related to the support of various languages under Fedora Core. iiimf o The default Input Method (IM) for Chinese (Simplified and Traditional), Japanese, and Korean has been changed to IIIMF -- the Internet/Intranet Input Method Framework. IIIMF is supported as a native GTK2 IM module, and also through XIM using the httx client. IIIMF supports the use of multiple Language Engines (LEs) at the same time; using the GNOME Input Method Language Engine Tool (GIMLET -- an applet) it is possible to switch between LEs of different languages inside GTK2 applications. IIIMF currently defaults to using Ctrl-Space or Shift-Space for toggling the input method on and off (Emacs users can use Ctrl-@ instead of Ctrl-Space to set the mark.) Depending on your selection at the language support screen during installation, one or more IIIMF language engines may be installed. The IIIMF server package (iiimf-server) will also be installed if a language engine has been selected. The language to language engine (LE) package mappings are as follows: o ja_JP -- iiimf-le-canna o zh_CN -- iiimf-le-chinput o zh_TW -- iiimf-le-xcin o ko_KR -- iiimf-le-hangul o {bn,gu,pa,ta,hi}_IN -- iiimf-le-unit Accordingly, input via IIIMF will be enabled if you have chosen one of the following as your default locale: o ja_JP o zh_CN o zh_TW o ko_KR o {bn,gu,pa,ta,hi}_IN To aid your use of IIIMF, if you have selected one of the above locales and you are using the GNOME Desktop, when you first login the GIMLET utility (part of the iiimf-gnome-im-switcher package) will automatically be added to your panel. GIMLET is a utility for switching between the different LEs that are installed on your system. Using a different language engine allows you to enter text in different languages. Alternatively you may add GIMLET manually to your panel by right clicking on the panel and selecting: Add to Panel -> GIMLET Should you wish to switch between IIIMF or the legacy input method framework XIM, you can use the system-switch-im application. After changing the input method framework your changes will be reflected when you next start the X Window System. Mail Server This section contains information related to the mail transport agents included with Fedora Core. mailman Earlier mailman RPMs installed all files under the /var/mailman/ directory. Unfortunately, this did not conform to the Filesystem Hierarchy Standard (FHS) and also created security violations when SELinux was enabled. If you previously had mailman installed and had edited files in /var/mailman/ (such as mm_cfg.py) you must move those changes to their new location, as documented in the following file: /usr/share/doc/mailman-*/INSTALL.REDHAT sendmail o By default, the Sendmail mail transport agent (MTA) does not accept network connections from any host other than the local computer. If you want to configure Sendmail as a server for other clients, you must edit /etc/mail/sendmail.mc and change the DAEMON_OPTIONS line to also listen on network devices (or comment out this option entirely using the dnl comment delimiter). You must then regenerate /etc/mail/sendmail.cf by running the following command (as root): make -C /etc/mail Note that you must have the sendmail-cf package installed for this to work. Server Configuration Tools This section contains information related to various server configuration tools. system-config-securitylevel The firewall constructed by the system-config-securitylevel configuration tool now allows CUPS and Multicast DNS (mDNS) browsing. Note that, at the present time, these services cannot be disabled by system-config-securitylevel. Sound and Video This section contains information related to multimedia applications. k3b Past users of the CD/DVD burning application k3b may notice that the program k3bsetup is missing. This is because k3bsetup is not necessary under Fedora Core 3. Web Server This section contains information related to Web-related tools. crypto-utils The certwatch(1) tool has been added to the crypto-utils package. This tool is used to send warning mail to root when any configured SSL certificates have expired or are approaching the expiration date. By default, the tool checks any certificates that are enabled in the mod_ssl configuration. httpd By default, the httpd daemon is now started using the C locale, rather than using the configured system locale setting. This behavior can be changed by setting the HTTPD_LANG variable in the /etc/sysconfig/httpd file. php The gd, mbstring, and ncurses extensions have been moved to the php-gd, php-mbstring, and php-ncurses packages, respectively. Note that you will need to install these packages manually (if required) when upgrading from an earlier release. Windows File Server This section contains information related to Samba, software that makes it possible to share files between Linux and Windows systems. samba Browsing of Windows shares (also known as SMB browsing) fails on Fedora Core 3 systems that have the standard firewall configured. This is most easily noticed in the failure of Nautilus to display shares. The failure is due to the firewall disrupting the broadcast mode of SMB browsing, which is Samba's default setting. There are two workarounds: o Configure a WINS server on the network, and set the "wins server" option in smb.conf to the address of the WINS server. o Disable the firewall Warning Depending on your system and network configurations, disabling the firewall can greatly increase the chance of your system being attacked and compromised. Make sure you fully understand the risks before undertaking this step. For additional information, refer to the following bug report: [8]https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=133478 X Window System This section contains information related to the X Window System implementation provided with Fedora Core. xorg-x11 o Users new to the X.org X11 implementation should take note of a few differences between it and the XFree86.org X11 implementation which shipped in previous Red Hat operating systems. In particular, the names of some files have changed: X Server Binary: o XFree86 X11: XFree86 o X.org X11: Xorg X Server Configuration File: o XFree86 X11: /etc/X11/XF86Config o X.org X11: /etc/X11/xorg.conf X Server Log File o XFree86 X11: /var/log/XFree86.$DISPLAY.log o X.org X11: /var/log/Xorg.$DISPLAY.log When configuring or troubleshooting your X server configuration, be sure that you are using the correct files. o There has been some confusion regarding font-related issues under the X Window System in recent versions of Fedora Core (and versions of Red Hat Linux before it.) At the present time, there are two font subsystems, each with different characteristics: - The original (15+ year old) subsystem is referred to as the "core X font subsystem". Fonts rendered by this subsystem are not anti-aliased, are handled by the X server, and have names like: -misc-fixed-medium-r-normal--10-100-75-75-c-60-iso8859-1 The newer font subsystem is known as "fontconfig", and allows applications direct access to the font files. Fontconfig is often used along with the "Xft" library, which allows applications to render fontconfig fonts to the screen with antialiasing. Fontconfig uses more human-friendly names like: Luxi Sans-10 Over time, fontconfig/Xft will replace the core X font subsystem. At the present time, applications using the Qt 3 or GTK 2 toolkits (which would include KDE and GNOME applications) use the fontconfig and Xft font subsystem; most everything else uses the core X fonts. In the future, Fedora Core may support only fontconfig/Xft in place of the XFS font server as the default local font access method. NOTE: An exception to the font subsystem usage outlined above is OpenOffice.org (which uses its own font rendering technology). If you wish to add new fonts to your Fedora Core 3 system, you must be aware that the steps necessary depend on which font subsystem is to use the new fonts. For the core X font subsystem, you must: 1. Create the /usr/share/fonts/local/ directory (if it doesn't already exist): mkdir /usr/share/fonts/local/ 2. Copy the new font file into /usr/share/fonts/local/ 3. Update the font information by issuing the following commands (note that, due to formatting restrictions, the following commands may appear on more than one line; in use, each command should be entered on a single line): ttmkfdir -d /usr/share/fonts/local/ -o /usr/share/fonts/local/fonts.scale mkfontdir /usr/share/fonts/local/ 4. If you had to create /usr/share/fonts/local/, you must then add it to the X font server (xfs) path: chkfontpath --add /usr/share/fonts/local/ Adding new fonts to the fontconfig font subsystem is more straightforward; the new font file only needs to be copied into the /usr/share/fonts/ directory (individual users can modify their personal font configuration by copying the font file into the ~/.fonts/ directory). After the new font has been copied, use fc-cache to update the font information cache: fc-cache <directory> (Where <directory> would be either the /usr/share/fonts/ or ~/.fonts/ directories.) Individual users may also install fonts graphically, by browsing fonts:/// in Nautilus, and dragging the new font files there. NOTE: If the font filename ends with ".gz", it has been compressed with gzip, and must be decompressed (with the gunzip command) before the fontconfig font subsystem can use the font. o Due to the transition to the new font system based on fontconfig/Xft, GTK+ 1.2 applications are not affected by any changes made via the Font Preferences dialog. For these applications, a font can be configured by adding the following lines to the file ~/.gtkrc.mine: style "user-font" { fontset = "<font-specification>" } widget_class "*" style "user-font" (Where <font-specification> represents a font specification in the style used by traditional X applications, such as "-adobe-helvetica-medium-r-normal--*-120-*-*-*-*-*-*".) Miscellaneous Notes This section contains information related to packages that do not fit in any of the proceeding categories. compat-db C++ and TCL bindings are no longer contained in the compat-db package. Applications requiring these bindings must be ported to the currently-shipping DB library. nscd The nscd name service cache daemon may now maintain a persistent cache across restarts or system reboots. Each database (user, group, and host, respectively) can be made selected to be persistent by setting the appropriate line in /etc/nscd.conf to "yes". Entries are not removed from the cache until they are proven to be no longer of interest. All entries whose time-to-live expires but are otherwise interesting are automatically reloaded, which helps in situations where the directory and name services become temporarily unavailable. The nscd name service daemon is also able to communicate faster with client programs. This feature must be enabled explicitly by setting the "shared" entry for the appropriate database in /etc/nscd.conf to "yes". udev Fedora Core 3 has switched from a static /dev/ directory to one that is dynamically managed via udev. This allows device nodes to be created on demand as drivers are loaded. For more information on udev, refer to the udev(8) man page and the following link: [9]http://people.redhat.com/~harald/udev.html Additional rules for udev should be placed in a separate file in the /etc/udev/rules.d/ directory. Additional permission rules for udev should be placed in a separate file in the /etc/udev/permissions.d/ directory. Systems upgraded to Fedora Core 3 using Anaconda will automatically be reconfigured to use udev. However (although NOT recommended) it is possible to perform a "live" upgrade to udev using the following steps: 1. Ensure that you are running a 2.6 kernel 2. Ensure that /sys/ is mounted 3. Install the initscripts RPM supplied with Fedora Core 3 4. Install the new udev RPM supplied with Fedora Core 3 5. Execute /sbin/start_udev 6. Install the new mkinitrd RPM supplied with Fedora Core 3 7. Perform one of the following steps: . Install the new kernel RPM supplied with Fedora Core 3 OR: . Re-run mkinitrd for your existing kernel(s) Warning Improperly performing these steps can result in a system configuration that will not boot properly. Packages Added/Removed/Deprecated This section contains lists of packages that fit into the following categories: o Packages that have been added to Fedora Core 3 o Packages that have been removed from Fedora Core 3 o Packages that have been deprecated, and may be removed from a future release of Fedora Core Packages Added The following packages have been added to Fedora Core 3: o Canna-libs (i386) o FreeWnn-libs (i386) o HelixPlayer o ImageMagick (i386) o ImageMagick-c++ (i386) o NetworkManager o NetworkManager-gnome o Omni (i386) o Pyrex o SDL (i386) o SDL_image (i386) o SDL_mixer (i386) o SDL_net (i386) o VFlib2 (i386) o Xaw3d (i386) o aiksaurus (i386) o aiksaurus (x86_64) o aiksaurus-devel o aiksaurus-gtk (i386) o aiksaurus-gtk (x86_64) o aiksaurus-gtk-devel o alchemist (i386) o alsa-lib (i386) o apr (i386) o arptables_jf o arts (i386) o aspell (i386) o aspell-af o aspell-bg o aspell-br o aspell-ca o aspell-cs o aspell-cy o aspell-el o aspell-fo o aspell-ga o aspell-gd o aspell-gl o aspell-hr o aspell-ia o aspell-id o aspell-it o aspell-pl o at-spi (i386) o audiofile (i386) o audit o authd o beecrypt (i386) o bind-libs (i386) o blas (i386) o bluez-libs (i386) o bluez-utils-cups o bogl (i386) o boost (i386) o bzflag o cdparanoia-libs (i386) o compat-db (i386) o compat-gcc (x86_64) o compat-gcc-c++ (x86_64) o compat-gcc-g77 o compat-gcc-java o compat-gcc-objc o compat-libgcj o compat-libgcj-devel o compat-libstdc++ (x86_64) o compat-libstdc++-devel (x86_64) o compat-openldap (i386) o compat-openldap (x86_64) o compat-slang o crash o createrepo o crypto-utils o cscope o curl (i386) o cyrus-sasl-gssapi (i386) o cyrus-sasl-md5 (i386) o cyrus-sasl-ntlm (i386) o cyrus-sasl-ntlm (x86_64) o cyrus-sasl-plain (i386) o cyrus-sasl-sql (i386) o cyrus-sasl-sql (x86_64) o dasher o db4-java o dbh (i386) o dbus (i386) o dbus-glib (i386) o dbus-python o device-mapper (i386) o dhcpv6 o dhcpv6_client o diskdumputils o distcache (i386) o dmraid o docbook-simple o docbook-slides o ecj o eel2 (i386) o elfutils (i386) o elfutils-libelf (i386) o emacspeak o epiphany-devel o eruby-libs (i386) o esound (i386) o evolution-connector o evolution-data-server (i386) o evolution-data-server (x86_64) o evolution-data-server-devel o evolution-webcal o fedora-release o festival o firefox o flac (i386) o fonts-xorg-100dpi o fonts-xorg-75dpi o fonts-xorg-ISO8859-14-100dpi o fonts-xorg-ISO8859-14-75dpi o fonts-xorg-ISO8859-15-100dpi o fonts-xorg-ISO8859-15-75dpi o fonts-xorg-ISO8859-2-100dpi o fonts-xorg-ISO8859-2-75dpi o fonts-xorg-ISO8859-9-100dpi o fonts-xorg-ISO8859-9-75dpi o fonts-xorg-base o fonts-xorg-cyrillic o fonts-xorg-syriac o fonts-xorg-truetype o freeglut (i386) o fribidi (i386) o g-wrap (i386) o gail (i386) o gamin (i386) o gamin (x86_64) o gamin-devel o gcc4 o gcc4-c++ o gcc4-gfortran o gd (i386) o gda-mysql o gda-odbc o gda-postgres o gdk-pixbuf (i386) o gettext-devel o ghostscript (i386) o gimp-print (i386) o glib (i386) o gmp (i386) o gnome-desktop (i386) o gnome-keyring (i386) o gnome-keyring-manager o gnome-mag (i386) o gnome-nettool o gnome-panel (i386) o gnome-speech (i386) o gnome-spell (i386) o gnome-volume-manager o gnuplot-emacs o gnutls (i386) o gnutls (x86_64) o gnutls-devel o gok-devel o gphoto2 (i386) o gpm (i386) o gsl (i386) o gstreamer (i386) o gtk+ (i386) o gtk-engines (i386) o gtk2-engines (i386) o gtkhtml2 (i386) o gtkhtml3 (i386) o gtksourceview (i386) o gtkspell (i386) o guile (i386) o hal (i386) o hal (x86_64) o hal-cups-utils o hal-devel o hal-gnome o hesiod (i386) o howl o howl-devel o howl-libs (i386) o howl-libs (x86_64) o httpd-suexec o iiimf-gnome-im-switcher o iiimf-le-chinput o iiimf-le-sun-thai o iiimf-libs o iiimf-libs-devel o imlib (i386) o java-1.4.2-gcj-compat o java-1.4.2-gcj-compat-devel o jpackage-utils o katana o katana-build o kde-i18n-Bulgarian o kdeaddons-xmms o kdebase (i386) o kdelibs (i386) o kdemultimedia (i386) o kdenetwork-nowlistening o kdewebdev o kdewebdev-devel o kinput2 o krb5-auth-dialog o lapack (i386) o lesstif (i386) o libaio (i386) o libao (i386) o libavc1394 (i386) o libbonoboui (i386) o libbtctl (i386) o libbtctl-devel o libc-client (i386) o libcap (i386) o libcroco (i386) o libdbi (i386) o libdv (i386) o libesmtp (i386) o libexif (i386) o libf2c (i386) o libgail-gnome (i386) o libgal2 (i386) o libgcrypt (i386) o libgda (i386) o libgda (x86_64) o libgda-devel o libgfortran (i386) o libgfortran (x86_64) o libghttp (i386) o libglade2 (i386) o libgnat o libgnome (i386) o libgnomecanvas (i386) o libgnomedb (i386) o libgnomedb (x86_64) o libgnomedb-devel o libgnomeprint22 (i386) o libgnomeprintui22 (i386) o libgnomeui (i386) o libgpg-error (i386) o libgsf (i386) o libgtop2 (i386) o libidn (i386) o libidn (x86_64) o libidn-devel o libieee1284 (i386) o libmng (i386) o libmudflap (i386) o libmudflap (x86_64) o libmudflap-devel o libmusicbrainz (i386) o libofx (i386) o libogg (i386) o libpcap (i386) o libpng10 (i386) o libraw1394 (i386) o librsvg2 (i386) o libsepol (i386) o libsepol (x86_64) o libsepol-devel o libsilc o libsilc-devel o libsilc-doc o libsoup (i386) o libtabe (i386) o libtermcap (i386) o libtheora (i386) o libtheora (x86_64) o libtheora-devel o libtool-libs (i386) o libtool-libs13 (i386) o libungif (i386) o libusb (i386) o libuser (i386) o libvorbis (i386) o libwmf (i386) o libwmf (x86_64) o libwmf-devel o libwnck (i386) o libwpd (i386) o libwvstreams (i386) o libxfce4mcs (i386) o libxfce4util (i386) o libxfcegui4 (i386) o libxklavier (i386) o libxslt (i386) o linuxwacom o linuxwacom-devel o lm_sensors (i386) o lockdev (i386) o memtest86+ o mikmod (i386) o mikmod-devel o mod_authz_ldap o module-init-tools o mozilla-nspr (i386) o mozilla-nss (i386) o mysql (i386) o nautilus-cd-burner-devel o neon (i386) o net-snmp-libs (i386) o net-snmp-libs (x86_64) o netpbm (i386) o newt (i386) o newt-perl o nss_db (i386) o numactl o octave (i386) o octave-devel o openh323 (i386) o openhbci (i386) o openjade (i386) o openldap-servers-sql o openmotif (i386) o openmotif21 o openobex (i386) o openssl096b (i386) o openswan o ots (i386) o pam_ccreds (i386) o pam_ccreds (x86_64) o pam_passwdqc (i386) o pam_passwdqc (x86_64) o pcre (i386) o perl (i386) o php-gd o php-mbstring o php-ncurses o pilot-link (i386) o postgresql-libs (i386) o pwlib (i386) o python-ldap o qt (i386) o qt-config o readline (i386) o redhat-artwork (i386) o redhat-lsb (x86_64) o rpm-libs o ruby-libs (i386) o samba-common (i386) o sane-backends (i386) o scrollkeeper (i386) o selinux-policy-strict o selinux-policy-strict-sources o selinux-policy-targeted o selinux-policy-targeted-sources o sg3_utils o slang (i386) o speex (i386) o synaptics o sysfsutils o sysfsutils-devel o system-switch-im o tcl (i386) o tclx (i386) o tcp_wrappers (i386) o theora-tools o thunderbird o tk (i386) o tn5250 o tn5250-devel o totem o ttfonts-bn o ttfonts-gu o ttfonts-hi o ttfonts-pa o ttfonts-ta o unixODBC (i386) o unixODBC-kde (i386) o utempter (i386) o valgrind o valgrind-callgrind o vino o vte (i386) o w3c-libwww (i386) o xfce4-iconbox o xfce4-systray o xffm-icons o xfprint o xmlsec1 (i386) o xmlsec1-openssl (i386) o xorg-x11-Xdmx o xorg-x11-deprecated-libs (i386) o xorg-x11-deprecated-libs (x86_64) o xorg-x11-deprecated-libs-devel Packages Removed The following packages have been removed from Fedora Core 3: o FreeWnn-common o Gtk-Perl o Wnn6-SDK o Wnn6-SDK-devel o ac-archive o anaconda-images o ant o ant-core o ant-devel o ant-optional o aspell-pt_BR o bcel o bcel-devel o bluez-pan o bluez-sdp o bluez-sdp-devel o chromium o commons-beanutils o commons-beanutils-devel o commons-collections o commons-collections-devel o commons-dbcp o commons-dbcp-devel o commons-digester o commons-digester-devel o commons-fileupload o commons-fileupload-devel o commons-logging o commons-logging-devel o commons-modeler o commons-modeler-devel o commons-pool o commons-pool-devel o compat-gcc-g77 o comps o cup o cup-devel o dev o devlabel o dvdrecord o fam (i386) o fam (x86_64) o fam-devel o fedora-release o gcc-gnat o gcc34 o gcc34-c++ o gcc34-java o glade o gqview o gtkam o gtkam-gimp o gtkglarea o iiimf-client-lib o iiimf-client-lib-devel o iiimf-le-inpinyin o iiimf-le-newpy o iiimf-protocol-lib o iiimf-protocol-lib-devel o imlib-cfgeditor o iscsi o jaf o jaf-devel o jakarta-regexp o jakarta-regexp-devel o javamail o javamail-devel o junit o junit-devel o kde-i18n-Korean o kde-i18n-Lithuanian o kernel-source o kinput2-canna-wnn6 o libgcj34 o libgcj34-devel o libgnat o libgnomeprint o libgnomeprint-devel o libgnomeprintui o libgnomeprintui-devel o libole2 o libole2-devel o librep o librep-devel o libstdc++34 o libstdc++34-devel o licq o licq-gnome o licq-kde o licq-qt o licq-text o linc o linc-devel o lvm o magicdev o mod_jk2 o modutils o mx4j o mx4j-devel o mx4j-tools o mysql-jdbc o mysql-jdbc-tomcat o ncurses-c++-devel o njamd o nss_db-compat o pidentd o policy o policy-sources o policy-strict-sources o printman o python-optik o quanta o quanta-devel o raidtools o redhat-java-rpm-scripts o rep-gtk o samba (i386) o sawfish o servletapi o servletapi-devel o shapecfg o struts o struts-webapps o system-config-proc o tomcat o tomcat-devel o tomcat-libs o tomcat-test o unarj o xalan-j o xalan-j-devel o xalan-j-xsltc o xerces-j o xerces-j-devel o xffm-icons o xorg-x11-100dpi-fonts o xorg-x11-75dpi-fonts o xorg-x11-ISO8859-14-100dpi-fonts o xorg-x11-ISO8859-14-75dpi-fonts o xorg-x11-ISO8859-15-100dpi-fonts o xorg-x11-ISO8859-15-75dpi-fonts o xorg-x11-ISO8859-2-100dpi-fonts o xorg-x11-ISO8859-2-75dpi-fonts o xorg-x11-ISO8859-9-100dpi-fonts o xorg-x11-ISO8859-9-75dpi-fonts o xorg-x11-base-fonts o xorg-x11-cyrillic-fonts o xorg-x11-libs-data o xorg-x11-syriac-fonts o xorg-x11-truetype-fonts Packages Deprecated The following packages have been deprecated, and may be removed from a future release of Fedora Core: o dbskkd-cdb -- Only used by deprecated package skkinput o FreeWnn -- Only used by deprecated package kinput2-canna-wnn6 o miniChinput -- IIIMF is the recommended input method o nabi -- IIIMF is the recommended input method o ncpfs -- No longer part of Fedora Core profile o skkinput -- IIIMF is the recommended input method o xcin -- IIIMF is the recommended input method An Overview of the Fedora Project The goal of the Fedora Project is to work with the Linux community to build a complete, general-purpose operating system exclusively from open source software. Development will be done in a public forum. The project will produce time-based releases of Fedora Core about 2-3 times a year, with a public release schedule. The Red Hat engineering team will continue to participate in building Fedora Core and will invite and encourage more outside participation than was possible in the past. By using this more open process, we hope to provide an operating system more in line with the ideals of free software and more appealing to the open source community. For more information, refer to the Fedora Project website: [10]http://fedora.redhat.com/ In addition to the website, the following mailing lists are available: o fedora-list(a)redhat.com -- For users of Fedora Core releases o fedora-test-list(a)redhat.com -- For testers of Fedora Core test releases o fedora-devel-list(a)redhat.com -- For developers, developers, developers o fedora-docs-list(a)redhat.com -- For participants of the docs project To subscribe to any of these lists, send an email with the word "subscribe" in the subject to <listname>-request (where <listname> is one of the above list names.) NOTE: If you have subscribed in the past to rhl-list, rhl-beta-list, rhl-devel-list, or rhl-docs-list, your subscriptions have been retained. The Fedora Project also includes an IRC (Internet Relay Chat) channel. IRC is a real-time, text-based form of communication. With it, you can have conversations with multiple people in an open channel or chat with someone privately one-on-one. To talk with other Fedora Project participants via IRC, access freenode IRC network. Initially, you can use irc.freenode.net as the IRC server, although you may decide to select a server that is geographically closer to you. Refer to the freenode website ([11]http://www.freenode.net/) for more information. Fedora Project participants frequent the #fedora channel, while Fedora Project developers can often be found on the #fedora-devel channel. Some of the larger projects may have their own channels as well; this information can be found on the project pages. NOTE: Red Hat has no control over the Fedora IRC channels or their content. ( x86_64 ) References Visible links 1. http://www.gnu.org/licenses/fdl.html 2. http://fedora.redhat.com/docs/selinux-faq/ 3. http://www.redhat.com/archives/fedora-desktop-list/2004-June/msg00007.html 4. http://mail.gnome.org/archives/desktop-devel-list/2004-June/msg00370.html 5. http://platan.vc.cvut.cz/ftp/pub/vmware/ 6. http://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=119474 7. http://i2o.shadowconnect.com/ 8. https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=133478 9. http://people.redhat.com/~harald/udev.html 10. http://fedora.redhat.com/ 11. http://www.freenode.net/ -- ----- End forwarded message -----

Nov. 8, 2004

Re: [Wlug] Mandrake 10.1 Official ISOs

by Brian J. Conway

On Sun, 31 Oct 2004 16:30:23 -0800 (PST) J Schonberg <schonm(a)yahoo.com> wrote: > I would really like to know what version of ld they are using with > Mandrake 10.1. Something as simple as ld --version > > Is there anyway for me to find out without downloading many megs of > data? In general, a list of RPM versions would be lovely. ftp://sunsite.uio.no/pub/linux/Mandrakelinux/official/10.1/i586/media/main/binutils-2.15.90.0.3-1mdk.i586.rpm http://sources.redhat.com/binutils/ Brian J. Conway bconway(at)alum.wpi.edu "LINUX is obsolete" - Andrew S. Tanenbaum, creator of Minix - Jan 29, 1992

Nov. 1, 2004

Re: [Wlug] Mandrake 10.1 Official ISOs

by J Schonberg

I would really like to know what version of ld they are using with Mandrake 10.1. Something as simple as ld --version Is there anyway for me to find out without downloading many megs of data? In general, a list of RPM versions would be lovely. Jason. --- "Brian J. Conway" <bconway(a)alum.wpi.edu> wrote: > Mandrake 10.1 Official is now available for download and/or FTP > install, > but the ISOs (GPL) won't be available on the mirrors for 3 weeks. > I > scoured for them and found them here, in case anyone's interested: > > http://games.gci.net/pub/Linux/Mandrake/Mandrakelinux-10.1-Official/ > > > It took a couple connection attempts (I assume they're limiting > connections), but now I have two ISOs maxing out my cable modem at > 395 > KB/s. Finding the official md5sums and checking the images are an > exercise left to the reader. > > Brian J. Conway > bconway(at)alum.wpi.edu > > "LINUX is obsolete" > - Andrew S. Tanenbaum, creator of Minix - Jan 29, 1992 > _______________________________________________ > Wlug mailing list > Wlug(a)mail.wlug.org > http://mail.wlug.org/mailman/listinfo/wlug > __________________________________ Do you Yahoo!? Read only the mail you want - Yahoo! Mail SpamGuard. http://promotions.yahoo.com/new_mail

Nov. 1, 2004

Mandrake 10.1 Official ISOs

by Brian J. Conway

Mandrake 10.1 Official is now available for download and/or FTP install, but the ISOs (GPL) won't be available on the mirrors for 3 weeks. I scoured for them and found them here, in case anyone's interested: http://games.gci.net/pub/Linux/Mandrake/Mandrakelinux-10.1-Official/ It took a couple connection attempts (I assume they're limiting connections), but now I have two ISOs maxing out my cable modem at 395 KB/s. Finding the official md5sums and checking the images are an exercise left to the reader. Brian J. Conway bconway(at)alum.wpi.edu "LINUX is obsolete" - Andrew S. Tanenbaum, creator of Minix - Jan 29, 1992

Nov. 1, 2004

RE: [Wlug] Samba PDC Question

by Martin, Eric

If the install base is NT based, you could use hfnetchk (which SUS is based on) to check, and kixtart to do the grunt work of patching. Eric -----Original Message----- From: Keller, Tim [mailto:Tim.Keller@stratus.com] Sent: Thursday, October 28, 2004 3:14 PM To: 'Chuck Haines'; 'Worcester Linux Users Group' Subject: RE: [Wlug] Samba PDC Question Chuck, I'm not sure what versions of windows your have in your install base, however the easiest thing is to just configure them to download and install the patches themselves. As for the other programs, are these things that have to be "installed" or can they be raw copied out to the machines? If it's the latter, then you could just configure the login script stuff to run a local script that would check to see if it's already been run, if so do nothing, otherwise copy a bunch of files and import some registry keys, etc. Tim. -----Original Message----- From: Chuck Haines [mailto:chaines@gmail.com] Sent: Thursday, October 28, 2004 1:22 PM To: Worcester Linux Users Group Subject: [Wlug] Samba PDC Question Hello all, I'm running Samba 3 as my PDC for a large number of computers. What I'd like to be able to do is push out patches and programs to the computers that are logged into this domain. I know that with SMS and Windoze Active Directory I can do this, however I don't want to use Windows as my PDC. Does anyone know of any software I can use to accomplish this with samba? thanks, Chuck -- Chuck Haines chaines(a)gmail.com ------------------------------------------- Tau Kappa Epsilon Fraternity http://www.tkezm.org WPI Class of 2005 http://www.wpi.edu ------------------------------------------- AIM: CyberGrex YIM: CyberGrex_27 ICQ: 3707881 ------------------------------------------- _______________________________________________ Wlug mailing list Wlug(a)mail.wlug.org http://mail.wlug.org/mailman/listinfo/wlug _______________________________________________ Wlug mailing list Wlug(a)mail.wlug.org http://mail.wlug.org/mailman/listinfo/wlug

Oct. 30, 2004

Re: [Wlug] Linux Photo Printer recommendations

by John Stoffel

I just wanted to follow up about some issues I had with my new Epson R300 photo printer. Basically, each time I updated my debian systems (apt-get update) the printer would stop working. Something kept chaning the permissions of the /usr/lib/cups/backend/usb driver. After enough time fighting it, I finally found out that I needed to do a: dpkg-reconfigure cupsys to tell it to enable USB printer drivers. End of problem. It was a pain to figure out since I originally only had a network printer, so didn't even think of enabling USB printing. Silly me. Every day (or so) I find out new things about debian. Some good, some bad. My newest thing is NLE (Non-Linear Editing) of video. Kino is so-so, cinelerra crashes instantly all the time. Might try main-actor, but not sure I want to spend the money when I can just use my wife's machine and Windows software to edit. Sure, I should probably thing about a Mac OS X.x something box with their movie editing software.

Oct. 28, 2004

RE: [Wlug] Samba PDC Question

by Keller, Tim

Chuck, I'm not sure what versions of windows your have in your install base, however the easiest thing is to just configure them to download and install the patches themselves. As for the other programs, are these things that have to be "installed" or can they be raw copied out to the machines? If it's the latter, then you could just configure the login script stuff to run a local script that would check to see if it's already been run, if so do nothing, otherwise copy a bunch of files and import some registry keys, etc. Tim. -----Original Message----- From: Chuck Haines [mailto:chaines@gmail.com] Sent: Thursday, October 28, 2004 1:22 PM To: Worcester Linux Users Group Subject: [Wlug] Samba PDC Question Hello all, I'm running Samba 3 as my PDC for a large number of computers. What I'd like to be able to do is push out patches and programs to the computers that are logged into this domain. I know that with SMS and Windoze Active Directory I can do this, however I don't want to use Windows as my PDC. Does anyone know of any software I can use to accomplish this with samba? thanks, Chuck -- Chuck Haines chaines(a)gmail.com ------------------------------------------- Tau Kappa Epsilon Fraternity http://www.tkezm.org WPI Class of 2005 http://www.wpi.edu ------------------------------------------- AIM: CyberGrex YIM: CyberGrex_27 ICQ: 3707881 ------------------------------------------- _______________________________________________ Wlug mailing list Wlug(a)mail.wlug.org http://mail.wlug.org/mailman/listinfo/wlug

Oct. 28, 2004

Entry Level

by Micheal Bonner

Hello all .. I am new to this city .. and I was wondering .. i am looking for something entry level in tech.. I have been working as a food manger for soo long and looking for a change .. something that might allow me to learn and grow ... something to get my foot in the door .. i have good knowledge of linux and window .. anything to help .. advice ?

Oct. 28, 2004