March 2003 - WLUG - wlug.mailman3.com

acpi

by Wesley Allen

Hi gang, ACPI is FINALLY compiled into Mandrake's kernel; but I'm having a hitch. While the kernel will boot with acpi enabled every now and again, most times it gets to a point where keventd is called for and the kernel message is that it hasn't started yet. Any ideas what on earth might be happening? I'm going to the acpi list as well, but I'd see if any of you linux laptop users have had this problem (there are google hits for this problem, but I'm hitting a dead end there). Wes

March 31, 2003

Re: [Wlug] RAS server

by Stéphane Purnelle

Ok, but how to configure a ppp server with callback system ? And, how to route the ppp connection for acces to the LAN. Le sam 29/03/2003 à 07:33, Karl Hiramoto a écrit : > use the ssh server to login to your machine remotely. > > > man ssh > man sshd > > if you mean modem dial in support, you would probally want to setup a > ppp server. > > Stéphane Purnelle wrote: > > >Hi > > > >I would like make a RAS (Remote acces support) server on my linux. > >How make it ? > > > > > > > > > >_______________________________________________ > >Wlug mailing list > >Wlug(a)mail.wlug.org > >http://mail.wlug.org/mailman/listinfo/wlug > > > >

March 30, 2003

Re: [Wlug] stupid question - no such thing!

by Tom Guilderson

Wes, The best place to start is in the kernel source tarball for the version of your kernel. under the Documentation directory. In the usb directory there is a file philips.txt which I included below from 2.4.20 and there appears to be a website where you may find more. As I do not have a webcam I can't provide much more info - good luck! ---------------------------------------------------------------------------- This file contains some additional information for the Philips webcams. E-mail: webcam(a)smcc.demon.nl Last updated: 2001-09-24 The main webpage for the Philips driver is http://www.smcc.demon.nl/webcam/. It contains a lot of extra information, a FAQ, and the binary plugin 'PWCX'. This plugin contains decompression routines that allow you to use higher image sizes and framerates; in addition the webcam uses less bandwidth on the USB bus (handy if you want to run more than 1 camera simultaneously). These routines fall under an NDA, and may therefor not be distributed as source; however, its use is completely optional. You can build this code either into your kernel, or as a module. I recommend the latter, since it makes troubleshooting a lot easier. The built-in microphone is supported through the USB Audio class. When you load the module you can set some default settings for the camera; some programs depend on a particular image-size or -format and don't know how to set it properly in the driver. The options are: size Can be one of 'sqcif', 'qsif', 'qcif', 'sif', 'cif' or 'vga', for an image size of resp. 128x96, 160x120, 176x144, 320x240, 352x288 and 640x480 (of course, only for those cameras that support these resolutions). fps Specifies the desired framerate. Is an integer in the range of 4-30. fbufs This paramter specifies the number of internal buffers to use for storing frames from the cam. This will help if the process that reads images from the cam is a bit slow or momentarely busy. However, on slow machines it only introduces lag, so choose carefully. The default is 3, which is reasonable. You can set it between 2 and 5. mbufs This is an integer between 1 and 4. It will tell the module the number of buffers to reserve for mmap(), VIDIOCCGMBUF, VIDIOCMCAPTURE and friends. The default is 2, which is adequate for most applications (double buffering). Should you experience a lot of 'Dumping frame...' messages during grabbing with a tool that uses mmap(), you might want to increase if. However, it doesn't really buffer images, it just gives you a bit more slack when your program is behind. But you need a multi-threaded or forked program to really take advantage of these buffers. The absolute maximum is 4, but don't set it too high! Every buffer takes up 1.22 MB of RAM, so unless you have a lot of memory setting this to something more than 2 is an absolute waste. This memory is only allocated during open(), so nothing is wasted when the camera is not in use. power_save When power_save is enabled (set to 1), the module will try to shut down the cam on close() and re-activate on open(). This will save power and turn off the LED. Not all cameras support this though (the 645 and 646 don't have power saving at all), and some models don't work either (they will shut down, but never wake up). Consider this experimental. By default this option is disabled. compression (only useful with the plugin) With this option you can control the compression factor that the camera uses to squeeze the image through the USB bus. You can set the parameter between 0 and 3: 0 = prefer uncompressed images; if the requested mode is not available in an uncompressed format, the driver will silently switch to low compression. 1 = low compression. 2 = medium compression. 3 = high compression. High compression takes less bandwidth of course, but it could also introduce some unwanted artefacts. The default is 2, medium compression. See the FAQ on the website for an overview of which modes require compression. The compression parameter only applies to the Vesta & ToUCam cameras. The 645 and 646 have fixed compression parameters. leds This settings takes 2 integers, that define the on/off time for the LED (in milliseconds). One of the interesting things that you can do with this is let the LED blink while the camera is in use. This: leds=500,500 will blink the LED once every second. But with: leds=0,0 the LED never goes on, making it suitable for silent survaillance. By default the camera's LED is on solid while in use, and turned off when the camera is not used anymore. This parameter works only with the ToUCam range of cameras (730, 740, 750). For other cameras this command is silently ignored, and the LED cannot be controlled. dev_hint A long standing problem with USB devices is their dynamic nature: you never know what device a camera gets assigned; it depends on module load order, the hub configuration, the order in which devices are plugged in, and the phase of the moon (i.e. it can be random). With this option you can give the driver a hint as to what video device node (/dev/videoX) it should use with a specific camera. This is also handy if you have two cameras of the same model. A camera is specified by its type (the number from the camera model, like PCA645, PCVC750VC, etc) and optionally the serial number (visible in /proc/bus/usb/devices). A hint consists of a string with the following format: [type[.serialnumber]:]node The square brackets mean that both the type and the serialnumber are optional, but a serialnumber cannot be specified without a type (which would be rather pointless). The serialnumber is separated from the type by a '.'; the node number by a ':'. This somewhat cryptic syntax is best explained by a few examples: dev_hint=3,5 The first detected cam gets assigned /dev/video3, the second /dev/video5. Any other cameras will get the first free available slot (see below). dev_hint=645:1,680=2 The PCA645 camera will get /dev/video1, and a PCVC680 /dev/video2. dev_hint=645.0123:3,645.4567:0 The PCA645 camera with serialnumber 0123 goes to /dev/video3, the same camera model with the 4567 serial gets /dev/video0. dev_hint=750:1,4,5,6 The PCVC750 camera will get /dev/video1, the next 3 Philips cams will use /dev/video4 through /dev/video6. Some points worth knowing: - Serialnumbers are case sensitive and must be written full, including leading zeroes (it's treated as a string). - If a device node is already occupied, registration will fail and the webcam is not available. - You can have up to 64 video devices; be sure to make enough device nodes in /dev if you want to spread the numbers (this does not apply to devfs). After /dev/video9 comes /dev/video10 (not /dev/videoA). - If a camera does not match any dev_hint, it will simply get assigned the first available device node, just as it used to be. trace In order to better detect problems, it is now possible to turn on a 'trace' of some of the calls the module makes; it logs all items in your kernel log at debug level. The trace variable is a bitmask; each bit represents a certain feature. If you want to trace something, look up the bit value(s) in the table below, add the values together and supply that to the trace variable. Value Value Description Default (dec) (hex) 1 0x1 Module initialization; this will log messages On while loading and unloading the module 2 0x2 probe() and disconnect() traces On 4 0x4 Trace open() and close() calls Off 8 0x8 read(), mmap() and associated ioctl() calls Off 16 0x10 Memory allocation of buffers, etc. Off 32 0x20 Showing underflow, overflow and Dumping frame On messages 64 0x40 Show viewport and image sizes Off For example, to trace the open() & read() fuctions, sum 8 + 4 = 12, so you would supply trace=12 during insmod or modprobe. If you want to turn the initialization and probing tracing off, set trace=0. The default value for trace is 35 (0x23). Example: # modprobe pwc size=cif fps=15 power_save=1 The fbufs, mbufs and trace parameters are global and apply to all connected cameras. Each camera has its own set of buffers. size, fps, palette only specify defaults when you open() the device; this is to accommodate some tools that don't set the size or colour palette. You can change these settings after open() with the Video4Linux ioctl() calls. The default of defaults is QCIF size at 10 fps, BGR order. The compression parameter is semiglobal; it sets the initial compression preference for all camera's, but this parameter can be set per camera with the VIDIOCPWCSCQUAL ioctl() call. All parameters are optional. --------------------------------------------------------------------------- On 2003.03.28 22:42 Wesley Allen wrote: > Hi gang, > I've hit a snag with mdk 9.1, the driver for my web cam no > longer > supports the default palette for gnomemeeting. So it tells me to > check > my driver docs to see what palettes are supported.... where is a good > place to find kernel-driver docs? > > The module is pwc in case you were wondering..... > > Wes > -- > Wesley Allen <wallen(a)charter.net> > > > _______________________________________________ > Wlug mailing list > Wlug(a)mail.wlug.org > http://mail.wlug.org/mailman/listinfo/wlug > >

March 29, 2003

Re: [Wlug] RAS server

by Karl Hiramoto

use the ssh server to login to your machine remotely. man ssh man sshd if you mean modem dial in support, you would probally want to setup a ppp server. Stéphane Purnelle wrote: >Hi > >I would like make a RAS (Remote acces support) server on my linux. >How make it ? > > > > >_______________________________________________ >Wlug mailing list >Wlug(a)mail.wlug.org >http://mail.wlug.org/mailman/listinfo/wlug > > -- €º°`°º€ø,žž,ø€º°`°º€ø,žž,ø€º°`°º€ø,žž,ø€º°`°º€ø,žž,ø€º°`°º€ø Karl Hiramoto <karl(a)hiramoto.org> Work: 978-425-2090 ext 25 Cell: 508-517-4819 Personal web page: http://karl.hiramoto.org/ Freedom: http://www.technojihad.com/ Zoop Productions: http://www.zoop.org/ KTEQ Rapid City: http://www.kteq.org/ AOL IM ID = KarlH420 Yahoo_IM = karl_hiramoto €º°`°º€ø,žž,ø€º°`°º€ø,žž,ø€º°`°º€ø,žž,ø€º°`°º€ø,žž,ø€º°`°º€ø Anybody can win, unless there happens to be a second entry.

March 29, 2003

stupid question

by Wesley Allen

Hi gang, I've hit a snag with mdk 9.1, the driver for my web cam no longer supports the default palette for gnomemeeting. So it tells me to check my driver docs to see what palettes are supported.... where is a good place to find kernel-driver docs? The module is pwc in case you were wondering..... Wes -- Wesley Allen <wallen(a)charter.net>

March 29, 2003

Re: [Wlug] WLUG website idea

by Frank Sweetser

On Fri, Mar 28, 2003 at 08:22:40PM -0500, Andy Stewart wrote: > If you think this is a good idea, please send me e-mail with your name, > project name, and your involvement (doc writer, coder, tester, etc). I think that's a great idea! As for myself, I'm the primary maintainer of the (currently stagnant for quite a while) LANdb project, and I'm getting involved with a little beta testing and possibly some development of the access grid. -- Frank Sweetser fs at wpi.edu WPI Network Engineer

March 29, 2003

WLUG website idea

by Andy Stewart

HI everybody, I had an idea...let me know what you think of it. I was thinking about creating a part of the WLUG website that would be a set of links to open source projects in which WLUG members are actively involved. For example, I wrote the users' guide for the GimpPrint software, so there would be a link to the GimpPrint website. If you think this is a good idea, please send me e-mail with your name, project name, and your involvement (doc writer, coder, tester, etc). Thanks, Andy -- Andy Stewart, Founder Worcester Linux Users' Group Worcester, MA USA http://www.wlug.org

March 29, 2003

RAS server

by Stéphane Purnelle

Hi I would like make a RAS (Remote acces support) server on my linux. How make it ?

March 28, 2003

Re: [Wlug] Tonight...

by John Stoffel

Tom> Can not make it either. my wife is teaching and I have the twins. Tom> They are still a little too young to bring to a meeting! Didn't stop me, I brought my kid last night. Luckily my wife came and got him after work got out. :]

March 27, 2003

RE: [Wlug] Weird garbage characters in info/man

by Keller, Tim

Eureka! I can't take credit for finding the fix, my co-worker found it on Usenet via google groups... The temporary solution was to export LANG=en_US the permanent solution is to edit /etc/sysconfig/i18n to make it permanent. I hope this helps others... Tim. -----Original Message----- From: Keller, Tim [mailto:Tim.Keller@stratus.com] Sent: Thursday, March 27, 2003 9:06 AM To: 'wlug(a)mail.wlug.org' Subject: [Wlug] Weird garbage characters in info/man I just created a RH 8.0 box for testing and when I go into info, there's garbage characters all over the place. Here's an example from the "info rpm" page... rpm {âEURâEURq|âEURâEURâEURâEURquery} [selectâEURâEURoptions] [queryâEURâEURoptions] I'm connected to the box vis SSH using teh "F-Secure SSH" client for windows. I've never had an issue with any other box. It's almost like some library or character set didn't get installed... Thanks, Tim. _______________________________________________ Wlug mailing list Wlug(a)mail.wlug.org http://mail.wlug.org/mailman/listinfo/wlug

March 27, 2003